Smartcard Data Version; Smartcard Data Checksum; Status Mode Time-Out; Parameter Cloning - Emerson SP1201 Installation Manual

Safety Product
Introduction
Information information
11.39

SMARTCARD data version

Drive mode Regen
Bit SP
Coding
Range Regen
Default Regen
Update rate Background
Indicates the version number of the data block. This is intended to be used when data blocks are used as drive macros. If a version number is to be
stored with a data block this parameter should be set to the required version number before the data is transferred. Each time Pr 11.37 is changed by
the user the drive puts the version number of the currently viewed data block in this parameter.
11.40

SMARTCARD data checksum

Drive mode Regen
Bit SP
Coding
Range Regen
Update rate Background
Gives the checksum of the data block or the bytes left on the card if Pr 11.37 = 1000.
11.41

Status mode time-out

Drive mode Regen
Bit SP
Coding
Range Regen
Default Regen
Update rate Background
Sets the timeout for the drive display to revert to status mode from edit mode following no key presses. Although this parameter can be set to less
than 2s, the minimum timeout is 2s.
11.42

Parameter cloning

Drive mode Regen
Bit SP
Coding
Range Regen
Default Regen
Update rate Background
* Modes 1 and 2 are not US (i.e. not saved when drive parameters are saved), mode 3 and 4 are US.
Therefore this parameter can only be saved to EEPROM if it has a value of 0, 3 or 4.
Reading (1)
Setting Pr 11.42 to 1 and resetting the drive will load the parameters from the card into the drive parameter set and the drive EEPROM. All
SMARTCARD trips apply. When the action is complete this parameter is automatically reset to zero. Parameters are saved to drive EEPROM after
this action is complete.
NOTE
This operation is only performed if block 1 on the card is a complete copy of the EEPROM (i.e. types 1 to 5) and not a difference from default file. If
block 1 does not exist or the type is incorrect a C.typ trip occurs.
Programming (2)
Setting Pr 11.42 to 2 and resetting the drive will save the parameters in the drive EEPROM to a card, i.e. equivalent to writing 3001 to Pr x.00. All
SMARTCARD trips apply except C.Chg. If the data block already exists it is automatically over-written. When the action is complete this parameter is
automatically reset to zero.
Auto (3)
Changing Pr 11.42 to 3 and resetting the drive will save the complete parameter set from the EEPROM to the card. All SMARTCARD trips apply,
except C.Chg. If the data block already exists it is automatically overwritten.
If the card is removed when Pr 11.42 is set to 3 Pr 11.42 will be set to 0. If a card with a file 1 is inserted into a drive the drive must overwrite the file to
Unidrive SP Regen Installation Guide
Issue Number: 2
System Mechanical
design installation
FI DE Txt VM DP ND
0 to 9,999
0
FI DE Txt VM DP ND
1
0 to 65,335
FI DE Txt VM DP ND
0 to 250 s
240
FI DE Txt VM DP ND
1
0 to 4
0
www.controltechniques.com
Electrical Getting
Optimisation
installation started
RA NC NV PT US RW BU
1
RA NC NV PT US RW BU
1 1
RA NC NV PT US RW BU
1
RA NC NV PT US RW BU
1 *
Technical Component
Parameters
data
PS
1 1
PS
1
PS
1 1
PS
1 1
Diagnostics
sizing
161