Regen Mode State Diagram; Regen Mode States; Menu 6 Regen Parameter Descriptions - Emerson SP1201 Installation Manual

Safety Product
Introduction
Information information
Table 9-6 Regen mode state diagram
State Actions
DISABLE Disable inverter
REGEN_SYNC Enable inverter
REGEN_ACTIVE
TRIP Disable inverter
Table 9-7 Regen mode states
Drive Status Conditions
INHIBIT DISABLE_STATE
READY Not used
STOP Not used
SCAN SYNC_STATE
RUN Not used
ACUU Not used
DECEL Not used
DC_INJ Not used
ORIENTING Not used
TRIPPED TRIPPED_STATE
REGEN_ACTIVE ACTIVE_STATE
Table 9-8 Menu 6 Regen parameter descriptions
Parameter
6.15 Drive enable
6.16 Electricity cost per kWh
6.17 Reset energy meter
6.18 Time between filter changes
6.19 Filter change required / change done
6.20 Powered-up time: years.days
6.21 Powered-up time: hours.minutes
6.22 Run time: years.days
6.23 Run time: hours.minutes
6.24 Energy meter: MWh
6.25 Energy meter: kWh
6.26 Running cost
6.27 Time before filter change due
6.28 Select clock for trip log time sampling
6.29 Hardware enable
6.41 Drive event flags
6.42 Control word
6.43 Control word enable
6.44 Active supply
6.45 Force cooling fan to run at full speed
6.46
Normal low voltage supply
Disable multi-module drive module
6.49
number storing on trip
6.50 Drive comms state
RW Read / Write RO Read only
FI Filtered DE Destination
112
System Mechanical Electrical
design installation installation
Exit conditions
1. TripState! = NO_TRIP THEN TRIP_STATE
2. Enable THEN SYNC_STATE
1. TripState! = NO_TRIP THEN TRIP_STATE
2. Not Enable THEN DISABLE_STATE
3. Supply not okay THEN DISABLE_STATE
4. Synchronised THEN ACTIVE_STATE
1. TripState! = NO_TRIP THEN TRIP_STATE
2. Not Enable OR NOT synchronised THEN DISABLE_STATE
1. TripState! = NO_TRIP THEN DISABLE_STATE
Display
inh
SCAn
trip
act
Range( )
OFF (0) or On (1)
0.0 to 600.0 currency units per kWh
OFF (0) or On (1)
0 to 30,000 hrs
OFF (0) or On (1)
0 to 9.364 years.days
0 to 23.59 hours.minutes
0 to 9.364 years.days
0 to 23.59 hours.minutes
±999.9 MWh
±99.99 kWh
±32,000
0 to 30,000 hrs
OFF (0) or On (1)
OFF (0) or On (1)
0 to 65,535
0 to 32,767
OFF (0) or On (1)
OFF (0) or On (1)
OFF (0) or On (1)
Size 1: 48V, Size 2 and 3: 48V to 72V
OFF (0) or On (1)
0 to 3
Uni Unipolar Bi Bi-polar
NC Not cloned RA Rating dependent
www.controltechniques.com
Getting
Optimisation Parameters
started
Default( )
On (1)
0.0
OFF (0)
0
OFF (0)
OFF (0)
0
0
OFF (0)
OFF (0)
48
OFF (0)
Bit Bit parameter Txt
PT Protected US
Technical Component
data sizing
Type
RW Bit
RW Uni
RW Bit NC
RW Uni NC
RW Bit
RW Uni NC PT
RW Uni NC PT
RO Uni NC PT PS
RO Uni NC PT PS
RO Bi NC PT PS
RO Bi NC PT PS
RO Bi NC PT
RO Uni NC PT PS
RW Bit
RO Bit NC PT
RW Uni NC
RW Uni NC
RW Bit
RO Bit NC PT
RW Bit
RW Uni
RW Bit
RO Txt NC PT
Text string
User save PS Power down save
Unidrive SP Regen Installation Guide
Issue Number: 2
Diagnostics
US
US
US
PT
US
US
US
PT US
US