Panasonic FP-E Programming Manual page 1258

FP1/FP-M/FP2/FP2SH/FP10SH/FP3
Address
MEWNET-W/-P link
transmission error flag
R9050 [W/P LINK 1] for FP3/
FP10SH
[W LINK 1] for FP2/FP2SH
MEWNET-W/-P link
transmission error flag
R9051 [W/P LINK 2] for FP3/
FP10SH
[W LINK 2] for FP2/FP2SH
MEWNET-W/-P link
transmission error flag
R9052 [W/P LINK 3] for FP3/
FP10SH
[W LINK 3] for FP2/FP2SH
MEWNET-W/-P link
transmission error flag
R9053 [W/P LINK 4] for FP2/
FP10SH
[W LINK 4] for FP2SH
MEWNET-W/-P link
transmission error flag
R9054 [W/P LINK 5] for FP2/
FP10SH
[W LINK 5] for FP2SH
MEWNET-H link
transmission error flag
R9055
[H LINK 1]: for FP3/
FP10SH
MEWNET-H link
transmission error flag
R9056
[H LINK 2]: for FP3/
FP10SH
MEWNET-H link
transmission error flag
R9057
[H LINK 3]: for FP3/
FP10SH
Remote I/O transmis-sion
error flag (master 1)
R9058
(Available PLC: FP2/
FP2SH/FP3/FP10SH)
Remote I/O transmis-sion
error flag (master 2)
R9059
(Available PLC: FP2/
FP2SH/FP3/FP10SH)
Remote I/O transmission
error flag (master 3)
R905A
(Available PLC: FP2/
FP2SH/FP3/FP10SH)
Remote I/O transmis-sion
error flag (master 4)
R905B
(Available PLC: FP2/
FP2SH/FP3/FP10SH)
R905C to
Not used
R905F
5-170
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Name
When using MEWNET-W link unit or MEWNET-P link
unit:
- turns on when transmission error occurs at link 1.
- turns on when there is an error in the link area settings.
When using MEWNET-W link unit or MEWNET-P link
unit:
- turns on when transmission error occurs at link 2.
- turns on when there is an error in the link area settings.
When using MEWNET-W link unit or MEWNET-P link
unit:
- turns on when transmission error occurs at link 3.
- turns on when there is an error in the link area settings.
When using MEWNET-W link unit or MEWNET-P link
unit:
- turns on when transmission error occurs at link 4.
- turns on when there is an error in the link area settings.
When using MEWNET-W link unit or MEWNET-P link
unit:
- turns on when transmission error occurs at link 5.
- turns on when there is an error in the link area settings.
When using MEWNET -H link unit:
- turns on when transmission error occurs at H link 1.
- turns on when there is an error in the link area settings.
When using MEWNET -H link unit:
- turns on when transmission error occurs at H link 2.
- turns on when there is an error in the link area settings.
When using MEWNET-H link unit:
- turns on when transmission error occurs at H link 3.
- turns on when there is an error in the link area settings.
When using MEWNET -F (remote I/O) system:
- turns on when transmission error occurs on master 1.
- turns on when there is an error in the settings.
When using MEWNET -F (remote I/O) system:
- turns on when transmission error occurs on master 2.
- turns on when there is an error in the settings.
When using MEWNET -F (remote I/O) system:
- turns on when transmission error occurs on master 3.
- turns on when there is an error in the settings.
When using MEWNET -F (remote I/O) system:
- turns on when transmission error occurs on master 4.
- turns on when there is an error in the settings.
-
Description