D-Link DES-3010F Command Line Interface Manual page 164

create cpu access_profile
Purpose
Used to create an access profile specifically for CPU Interface Filtering on the Switch and to
define which parts of each incoming frame's header the Switch will examine. Masks can be
entered that will be combined with the values the Switch finds in the specified frame header
fields. Specific values for the rules are entered using the config cpu access_profile
command, below.
Syntax
create cpu access_profile profile_id <value 1-3> [ethernet {vlan | source_mac
<macmask> | destination_mac <macmask> | 802.1p | ethernet_type} | ip {vlan |
source_ip_mask <netmask> | destination_ip_mask <netmask> | dscp |
[icmp {type | code} | igmp {type} | tcp {src_port_mask <hex 0x0-0xffff> |
dst_port_mask <hex 0x0-0xffff>} | flag_mask [all | {urg | ack | psh | rst | syn | fin}]} |
udp {src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex 0x0-0xffff>} |
protocol_id_mask {user_mask <hex 0x0-0xffffffff>} ]} | packet_content_mask {offset 0-15
<hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff>| offset 16-
31 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> | {offset
32-47 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> |
{offset 48-63 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-
0xffffffff> | {offset 64-79 <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex 0x0-0xffffffff> <hex
0x0-0xffffffff>} ]
Description
The create cpu access_profile command is used to create an access profile used only for
CPU Interface Filtering. Masks can be entered that will be combined with the values the Switch
finds in the specified frame header fields. Specific values for the rules are entered using the
config cpu access_profile command, below.
profile_id <value 1-3>  Specifies an index number that will identify the access profile being
Parameters
created with this command.
ethernet  Specifies that the Switch will examine the layer 2 part of each packet header.
vlan  Specifies that the Switch will examine the VLAN part of each packet header.


source_mac <macmask> – Specifies to examine the source MAC address mask.

destination_mac <macmask> – Specifies to examine the destination MAC address mask.
802.1p  Specifies that the Switch will examine the 802.1p priority value in the frame's

header.
ethernet_type  Specifies that the Switch will examine the Ethernet type value in each

frame's header.
ip  Specifies that the Switch will examine the IP address in each frame's header.
vlan  Specifies a VLAN mask.

source_ip_mask <netmask>  Specifies an IP address mask for the source IP address.

destination_ip_mask <netmask>  Specifies an IP address mask for the destination IP

address.
dscp  Specifies that the Switch will examine the DiffServ Code Point (DSCP) field in

each frame's header.
icmp  Specifies that the Switch will examine the Internet Control Message Protocol

(ICMP) field in each frame's header.


igmp  Specifies that the Switch will examine each frame's Internet Group Management

Protocol (IGMP) field.
type  Specifies that the Switch will examine each frame's IGMP Type field.
DES-3000 Series Layer 2 Switch CLI Reference Manual
type  Specifies that the Switch will examine each frame's ICMP Type field.
code  Specifies that the Switch will examine each frame's ICMP Code field.
160