Seastar Solutions Optimus 360 Installation Manual page 6

iv
9.2.8 STEP 8 - Adjust Power Levels ................................. 9-13
9.2.9 STEP 9 - Sea Trial .................................................. 9-14
9.2.10 STEP 10 - Save the Joystick Tuning File ................. 9-15
9.3 Importing a Joystick Tuning File ........................................ 9-16
9.3.1 Using a Template File ............................................. 9-16
9.3.2 Replacing a Joystick ............................................... 9-16
9.3.3 Updating Joystick Firmware ..................................... 9-17
9.3.4 Basic Import Procedure .......................................... 9-17
10.0 Post-Installation Warranty Checklist .........................................10-1
11.0 Updating Firmware ................................................................. 10-1
12.0 Warranty ............................................................................ 12-1
12.1 Statement of Limited Warranty ....................................... 12-1
12.2 Return Goods Procedure ................................................ 12-1
12.3 Technical Support ......................................................... 12-1
Appendix A - Mounting Templates .................................................... A-1
A.1 Joystick ............................................................................ A-1
A.2 Control Head (Yanmar/Optimus) ......................................... A-3
Appendix B - Setup and Tuning with Datalink ..................................... B-1
B.1 Using Datalink .................................................................. B-1
B.2 System Setup .................................................................. B-3
B.2.1 System Parameters ................................................. B-3
B.2.2 Settings Menu Access ............................................ B-4
B.2.3 Cycle Power to System ............................................ B-4
B.3 Joystick Tuning Procedure ................................................. B-5
B.3.1 General Notes ........................................................ B-6
B.3.2 Before You Start ..................................................... B-6
B.3.3 STEP 1 - Import Engine-Specific Settings .................. B-7
B.3.4 STEP 1a - System .................................................... B-7
B.3.5 STEP 2 - Set Throttle Limits ...................................... B-7
B.3.6 STEP 3 - Run Throttle Wizards ................................. B-9
B.3.7 STEP 4 - Set Forward Heading Correction ................ B-10
B.3.8 STEP 5 - Balance Rotation Power ........................... B-11
B.3.9 STEP 6 - Set Sideways Rudder Angle ...................... B-12
B.3.10 STEP 7 - Balance Sideways Engine Power ............. B-13
B.3.11 STEP 8 - Adjust Power Levels ............................... B-14
B.3.12 STEP 9 - Sea Trial ................................................ B-15
B.3.13 STEP 10 - Saving the Joystick Tuning File .............. B-15
B.4 Adding a Second Control Station ...................................... B-16
B.4.1 Configure the Secondary Helm and CANtrak Display ..... B-16
B.4.2 Configure the Secondary Control Head (Yanmar Only) ... B-16
B.4.3 Configure the Secondary Joystick .............................. B-16
B.5 Importing a Joystick Tuning File ........................................ B-17
B.5.1 Configuring a Second Joystick ................................. B-17
B.5.2 Using a Template File ............................................. B-17
B.5.3 Replacing a Joystick ............................................... B-18
B.5.4 Updating Joystick Firmware ..................................... B-18
B.5.5 Basic Import Procedure .......................................... B-18
B.6 Yamaha EST Gateway Setup ............................................ B-20
B.6.1 System ................................................................. B-21
B.6.2 LPS Calibration ...................................................... B-21
© 2014 SeaStar Solutions Optimus 360 Installation Supplement, Rev. B