Data Port Configuration Menu - Verilink DIDCSU 2912 Manual

DIDCSU E1 Version
Data Port
Configuration
Menu
Figure 4-8

Data Port Configuration Menu

-- -- DIDCSU 2912 DATA PORT CONFIGURATION MENU -- DIDCSU 2912 DATA PORT CONFIGURATION MENU --
-- -- DIDCSU 2912 DATA PORT CONFIGURATION MENU -- DIDCSU 2912 DATA PORT CONFIGURATION MENU --
In) In) In) In) In Service In Service In Service In Service
Mn) Mn) Mn) Mn) Data Port Mode Data Port Mode Data Port Mode Data Port Mode
Cn) Cn) Cn) Cn) Clock Option Clock Option Clock Option Clock Option
On) On) On) On) Enable LOS detection Enable LOS detection Enable LOS detection Enable LOS detection
Ln) Ln) Ln) Ln) Control Lead Mode Control Lead Mode Control Lead Mode Control Lead Mode
SRn) Forced DTR/DSR SRn) Forced DTR/DSR SRn) Forced DTR/DSR SRn) Forced DTR/DSR
SSn) Forced RTS/CTS SSn) Forced RTS/CTS SSn) Forced RTS/CTS SSn) Forced RTS/CTS
SDn) Forced LLB/DCD SDn) Forced LLB/DCD SDn) Forced LLB/DCD SDn) Forced LLB/DCD
SMn) Forced RLB/TM SMn) Forced RLB/TM
SMn) Forced RLB/TM SMn) Forced RLB/TM
Cable Cable
Cable Cable
DPL Loopback DPL Loopback DPL Loopback DPL Loopback
Test Pattern Test Pattern
Test Pattern Test Pattern
Test Error Counter Test Error Counter Test Error Counter Test Error Counter
X) exit this screen X) exit this screen X) exit this screen X) exit this screen
A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 >
4-12
To access the Data Port Configuration Menu
from the Configuration Menu.
To change a port configuration, enter the command letter followed
by the port number. For example, to disable port 2 from service,
command In, enter "I2" (n is a variable that identifies the port
number).
PORT 1 PORT 1
PORT 1 PORT 1
YES YES YES YES
DCE DCE DCE DCE
ST ST ST ST
NO NO NO NO
AUTO AUTO AUTO AUTO
DSR/LOW DSR/LOW DSR/LOW DSR/LOW
CTS/LOW CTS/LOW CTS/LOW CTS/LOW
DCD/LOW DCD/LOW DCD/LOW DCD/LOW
TM /LOW TM /LOW
TM /LOW TM /LOW
DTR/LOW DTR/LOW
DTR/LOW DTR/LOW
RTS/LOW RTS/LOW
RTS/LOW RTS/LOW
LLB/LOW LLB/LOW
LLB/LOW LLB/LOW
RLB/LOW RLB/LOW
RLB/LOW RLB/LOW
PRESENT PRESENT
PRESENT PRESENT
DISABLE DISABLE DISABLE DISABLE
NONE NONE
NONE NONE
0 0 0 0
One of the functions of the Data Port Configuration Menu is to set
the communication handshake leads between the DIDCSU data port
and your equipment (DTE).
Note that the lead options swap inputs and outputs between the
DCE or DTE data port modes.
There are three controllable diagnostic leads at the data port
(which are set up via the Data Port Diagnostics Menu):
• RLB—Remote Loopback
• LLB—Local Loopback
• TM—Test Mode
Verilink DIDCSU 2912 User Manual
(Figure 4-8), enter "D"
PORT 2 PORT 2
PORT 2 PORT 2
YES YES YES YES
DCE DCE DCE DCE
ST ST ST ST
NO NO NO NO
AUTO AUTO AUTO AUTO
DSR/LOW DSR/LOW DSR/LOW DSR/LOW
CTS/LOW CTS/LOW CTS/LOW CTS/LOW
DCD/LOW DCD/LOW DCD/LOW DCD/LOW
TM /LOW TM /LOW
TM /LOW TM /LOW
DTR/LOW DTR/LOW
DTR/LOW DTR/LOW
RTS/LOW RTS/LOW
RTS/LOW RTS/LOW
LLB/LOW LLB/LOW
LLB/LOW LLB/LOW
RLB/LOW RLB/LOW
RLB/LOW RLB/LOW
PRESENT PRESENT
PRESENT PRESENT
DISABLE DISABLE DISABLE DISABLE
NONE NONE
NONE NONE
0 0 0 0