Verilink DIDCSU 2912 Manual page 23

Figure 2-5 T1 Port Configuration Menu
-- -- DIDCSU 2912 T1 PORT CONFIGURATION MENU -- DIDCSU 2912 T1 PORT CONFIGURATION MENU --
-- -- DIDCSU 2912 T1 PORT CONFIGURATION MENU -- DIDCSU 2912 T1 PORT CONFIGURATION MENU --
In) In) In) In) In Service In Service In Service In Service
Fn) Fn) Frame Format Frame Format
Fn) Fn) Frame Format Frame Format
Ln) Ln) Ln) Ln) Line Coding Line Coding Line Coding Line Coding
Bn) Bn) Bn) Bn) Line Build Out Line Build Out Line Build Out Line Build Out
NDn) Network Density NDn) Network Density NDn) Network Density NDn) Network Density
NLn) Network Initiated Loop NLn) Network Initiated Loop NLn) Network Initiated Loop NLn) Network Initiated Loop
An) An) An) An) Alarm Declare Time(sec) Alarm Declare Time(sec) Alarm Declare Time(sec) Alarm Declare Time(sec)
DLn) FDL Enable DLn) FDL Enable DLn) FDL Enable DLn) FDL Enable
PRM Enable PRM Enable PRM Enable PRM Enable
En) En) Enable Inband/ISDN Enable Inband/ISDN
En) En) Enable Inband/ISDN Enable Inband/ISDN
Sn) Sn) Sn) Sn) Inband Timeslot Inband Timeslot Inband Timeslot Inband Timeslot
F) FDL configuration F) FDL configuration
F) FDL configuration F) FDL configuration
T) Timing T) Timing
T) Timing T) Timing
X) Exit this screen X) Exit this screen
X) Exit this screen X) Exit this screen
A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 >
Place Ports In
Service
Select ESF Framing
Select B8ZS Line
Coding
Set Line Build Out
to 0db
Set Density
Enforcement to
None
PORT 1 PORT 1
PORT 1 PORT 1
YES YES YES YES
SF SF
SF SF
AMI AMI AMI AMI
0db 0db 0db 0db
NONE NONE NONE NONE
NO NO NO NO
0 0 0 0
NO NO NO NO
NO NO NO NO
both dis both dis
both dis both dis
1 1 1 1
13. In the T1 Port Configuration Menu, type the letter "I" and the
number "1", press E
place Net Port 1 In Service. Type "I2", press E
respond by pressing "Y", E
NOTE: For the remainder of this section you will not be instructed
each time you should press the E
used after each command or text entry.
14. Type "F1", and "2" for ESF framing for Net Port 1. Type "F2"
and "2" for ESF framing for Net Port 2.
15. Type "L1", then "2" to select B8ZS as the line coding for Net
Port 1. Type "L2", then "2" to select B8ZS as the line coding for
Net Port 2.
16. Type "B1", then "1" to select 0db as the line build out for Net
Port 1. Type "B2", then "1" to select 0db as the line build out
for Net Port 2.
17. Type "ND1", then "1" to select NONE as the network density
for Net Port 1. Type "ND2", then "1" to select NONE as the
network density for Net Port 2.
Verilink DIDCSU 2912 User Manual
PORT 2 PORT 2
PORT 2 PORT 2
YES YES YES YES
ESF ESF
ESF ESF
AMI AMI AMI AMI
0db 0db 0db 0db
NONE NONE NONE NONE
NO NO NO NO
0 0 0 0
NO NO NO NO
NO NO NO NO
both dis both dis
both dis both dis
1 1 1 1
, then type "Y",and press E
NTER
, to place Net Port 2 In Service.
NTER
NTER
DIDCSU 2912 Quick Set-Up
, to
NTER
, then
NTER
key. In general, E
NTER
2-5
is