Verilink DIDCSU 2912 Manual page 33

Figure 2-17 Configuration Menu
-- DIDCSU 2912 CONFIGURATION MENU -- -- DIDCSU 2912 CONFIGURATION MENU -- -- DIDCSU 2912 CONFIGURATION MENU -- -- DIDCSU 2912 CONFIGURATION MENU --
P) E1 port P) E1 port P) E1 port P) E1 port
X) exit this screen X) exit this screen X) exit this screen X) exit this screen
A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 >
Figure 2-18 E1 Port Configuration Menu
-- -- DIDCSU 2912 E1 PORT CONFIGURATION MENU -- DIDCSU 2912 E1 PORT CONFIGURATION MENU --
-- -- DIDCSU 2912 E1 PORT CONFIGURATION MENU -- DIDCSU 2912 E1 PORT CONFIGURATION MENU --
In) In) In) In) In Service In Service In Service In Service
En) En) En) En) CRC4 CRC4 CRC4 CRC4
Fn) Fn) Fn) Fn) Carrier Failure Alarm Carrier Failure Alarm Carrier Failure Alarm Carrier Failure Alarm
Sn) Sn) Sn) Sn) FASE Alarm Category FASE Alarm Category FASE Alarm Category FASE Alarm Category
Mn) Mn) Mn) Mn) Frame Mode Frame Mode Frame Mode Frame Mode
Nn) Nn) Nn) Nn) Alarm Declare Time(sec) Alarm Declare Time(sec) Alarm Declare Time(sec) Alarm Declare Time(sec)
Bn) Bn) Bn) Bn) Enable Inband Enable Inband Enable Inband Enable Inband
Ln) Ln) Ln) Ln) Inband Timeslot Inband Timeslot Inband Timeslot Inband Timeslot
C) CPE Side DIDCSU: C) CPE Side DIDCSU: C) CPE Side DIDCSU: C) CPE Side DIDCSU:
T) timing T) timing
T) timing T) timing
X) exit this screen X) exit this screen
X) exit this screen X) exit this screen
A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 >
A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 >
Place Ports In
Service
Select CRC-4
Select Carrier
Failure Alarm
D) data port D) data port D) data port D) data port
12. From the Configuration Menu
to access the E1 Port Configuration Menu
PORT 1 PORT 1
PORT 1 PORT 1
NO NO NO NO
NO NO NO NO
NO NO NO NO
MINOR MINOR MINOR MINOR
31 CHANNEL 31 CHANNEL 31 CHANNEL 31 CHANNEL 31 CHANNEL 31 CHANNEL 31 CHANNEL 31 CHANNEL
0 0 0 0
NO NO NO NO
0 0 0 0
NO NO NO NO
13. In the E1 Port Configuration Menu, type the letter "I", and the
number "1", then press E
place Net Port 1 In Service. Type "I2", press E
respond by pressing "Y", E
NOTE: For the remainder of this chapter you will not be instructed
each time you should press the E
used after each command or text entry.
14. Type "E1", and select "Y" to enable CRC-4 error detection for
Net Port 1. Type "E2", and select "Y" to enable CRC-4 error
detection for Net Port 2.
15. Type "F1", then "Y" to select Carrier Failure as an alarm
condition reported by Net Port 1. Type "F2", then "Y" to select
Carrier Failure for Net Port 2.
Verilink DIDCSU 2912 User Manual
(Figure
PORT 2 PORT 2
PORT 2 PORT 2
NO NO NO NO
NO NO NO NO
NO NO NO NO
MINOR MINOR MINOR MINOR
0 0 0 0
NO NO NO NO
0 0 0 0
, then type "Y"and press E
NTER
, to place Net Port 2 In Service.
NTER
NTER
DIDCSU 2912 Quick Set-Up
2-17), select option "P"
(Figure 2-18).
, to
NTER
, then
NTER
key. In general, E
NTER
2-15
is