Configuring The T1 Port - Verilink DIDCSU 2912 Manual

Configuring the
T1 Port
Figure 3-5 T1 Port Configuration Menu
-- -- DIDCSU 2912 T1 PORT CONFIGURATION MENU -- DIDCSU 2912 T1 PORT CONFIGURATION MENU --
-- -- DIDCSU 2912 T1 PORT CONFIGURATION MENU -- DIDCSU 2912 T1 PORT CONFIGURATION MENU --
In) In) In) In) In Service In Service In Service In Service
Fn) Fn) Fn) Fn) Frame Format Frame Format Frame Format Frame Format
Ln) Ln) Ln) Ln) Line Coding Line Coding Line Coding Line Coding
Bn) Bn) Bn) Bn) Line Build Out Line Build Out Line Build Out Line Build Out
NDn) Network Density NDn) Network Density NDn) Network Density NDn) Network Density
NLn) Network Initiated Loop NLn) Network Initiated Loop NLn) Network Initiated Loop NLn) Network Initiated Loop
An) An) An) An) Alarm Declare Time(sec) Alarm Declare Time(sec) Alarm Declare Time(sec) Alarm Declare Time(sec)
DLn) FDL Enable DLn) FDL Enable DLn) FDL Enable DLn) FDL Enable
PRM Enable PRM Enable
PRM Enable PRM Enable
En) En) Enable Inband/ISDN Enable Inband/ISDN
En) En) Enable Inband/ISDN Enable Inband/ISDN
Sn) Sn) Inband Timeslot Inband Timeslot
Sn) Sn) Inband Timeslot Inband Timeslot
F) FDL configuration F) FDL configuration
F) FDL configuration F) FDL configuration
T) Timing T) Timing
T) Timing T) Timing
X) Exit this screen X) Exit this screen X) Exit this screen X) Exit this screen
A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 >
Table 3-4 T1 Port Configuration Menu Parameters
Command
In In Service: Use this option to place the port on line.
Fn Frame Format: Choose SF (Superframe) or ESF (Extended Superframe
Format) as dictated by the type of T1 facility provided. Contact your circuit
provider if the type of T1 framing is not known.
SF format provides traffic signaling and framing. It is sometimes referred to
as D4.
ESF format provides cyclic redundancy check, performance monitoring, data
checking, and link bits (Facilities Data Link, or FDL).
To access the T1 Port Configuration Menu, enter "P" from the
Configuration Menu.
To change a port configuration, enter the command letter followed
by the port number. For example, to remove Port 2 from service,
command In, enter "I2" (n is a variable that represents the port
number).
PORT 1 PORT 1
PORT 1 PORT 1
NO NO NO NO
SF SF SF SF
AMI AMI AMI AMI
0db 0db 0db 0db
NONE NONE NONE NONE
NO NO NO NO
0 0 0 0
NO NO NO NO
NO NO
NO NO
both dis both dis
both dis both dis
1 1
1 1
Description
Verilink DIDCSU 2912 User Manual
DIDCSU T1 Version
PORT 2 PORT 2
PORT 2 PORT 2
YES YES YES YES
ESF ESF ESF ESF
B8ZS B8ZS B8ZS B8ZS
0db 0db 0db 0db
NONE NONE NONE NONE
NO NO NO NO
0 0 0 0
NO NO NO NO
NO NO
NO NO
both dis both dis
both dis both dis
1 1
1 1
Options
Yes or No
1) SF
2) ESF
3-7