Configuration Menu; Configuring The E1 Port - Verilink DIDCSU 2912 Manual

Configuration Menu

Figure 4-4 Configuration Menu
-- DIDCSU 2912 CONFIGURATION MENU -- -- DIDCSU 2912 CONFIGURATION MENU -- -- DIDCSU 2912 CONFIGURATION MENU -- -- DIDCSU 2912 CONFIGURATION MENU --
P) E1 port P) E1 port P) E1 port P) E1 port
X) exit this screen X) exit this screen X) exit this screen X) exit this screen
A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 >
Configuring the
E1 Port
Figure 4-5 E1 Port Configuration Menu
-- -- -- -- DIDCSU 2912 E1 PORT CONFIGURATION MENU -- DIDCSU 2912 E1 PORT CONFIGURATION MENU -- DIDCSU 2912 E1 PORT CONFIGURATION MENU -- DIDCSU 2912 E1 PORT CONFIGURATION MENU --
In) In) In) In) In Service In Service In Service In Service
En) En) CRC4 CRC4
En) En) CRC4 CRC4
Fn) Fn) Carrier Failure Alarm Carrier Failure Alarm
Fn) Fn) Carrier Failure Alarm Carrier Failure Alarm
Sn) Sn) FASE Alarm Category FASE Alarm Category
Sn) Sn) FASE Alarm Category FASE Alarm Category
Mn) Mn) Frame Mode Frame Mode
Mn) Mn) Frame Mode Frame Mode
Nn) Nn) Alarm Declare Time(sec) Alarm Declare Time(sec)
Nn) Nn) Alarm Declare Time(sec) Alarm Declare Time(sec)
Bn) Bn) Enable Inband Enable Inband
Bn) Bn) Enable Inband Enable Inband
Ln) Ln) Inband Timeslot Inband Timeslot
Ln) Ln) Inband Timeslot Inband Timeslot
C) CPE Side DIDCSU: C) CPE Side DIDCSU: C) CPE Side DIDCSU: C) CPE Side DIDCSU:
T) timing T) timing T) timing T) timing
X) exit this screen X) exit this screen X) exit this screen X) exit this screen
A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 > A [0.0.0.204] [1,2] DIDCSU 2912 >
Use the Configuration Menu to configure your E1 port, data port,
or timing options. Access this menu from the Main Menu, by
entering "C".
D) data port D) data port D) data port D) data port
To access the E1 Port Configuration Menu, enter "P" from the
Configuration Menu.
To change a port configuration, enter the command letter followed
by the port number. For example, to remove port 2 from service,
command In, enter "I2" (n is a variable that identifies the port
number).
PORT 1 PORT 1 PORT 1 PORT 1
NO NO NO NO
NO NO
NO NO
NO NO
NO NO
MINOR MINOR
MINOR MINOR
31 CHANNEL 31 CHANNEL 31 CHANNEL 31 CHANNEL
31 CHANNEL 31 CHANNEL 31 CHANNEL 31 CHANNEL
0 0
0 0
NO NO
NO NO
0 0
0 0
NO NO NO NO
Verilink DIDCSU 2912 User Manual
DIDCSU E1 Version
PORT 2 PORT 2 PORT 2 PORT 2
NO NO NO NO
NO NO
NO NO
NO NO
NO NO
MINOR MINOR
MINOR MINOR
0 0
0 0
NO NO
NO NO
0 0
0 0
4-7