Bosch ICP-EZM2 Installer's Manual page 75

.
Phone Line
Phone line trouble voltage:
Control Panel Power Requirements
AC Input Line Voltage
Total Alarm Power:
Auxiliary Power:
Current Draw:
Voltage:
Battery:
EZPS Power Supply Requirements (not investigated by UL)
AC Input:
DC Output:
DX2010 Input Expander
Operating Voltage:
Current Draw:
Outputs:
Sensor Loop Terminal Wire Size:
Wire Length:
Operating Temperature:
Relative Humidity:
Sensor Loop Resistance:
Sensor Loop:
Bosch Security Systems, Inc. | 5/07 | F01U025147-01
Easy Series (ICP-EZM2) | Installer Guide | 7.0 Reference Materials
Trouble condition occurs when the phone line voltage is between 1.10 V and 4.75 V
Use a UL Listed 18 V Class 2 transformer (22 VAC, VA 50/60 Hz), or the EZPS
Power Supply (not investigated by UL).
1.4 A (AC power and standby battery; intrusion applications only).
With a 7.0 Ah battery, the following current draws apply to all outputs and devices
connected to the system:
•
Up to 170 mA for 24 hr for fire and combined fire/burglary applications
•
Up to 400 mA for 4 hr for UL burglary applications
•
Up to 1.2 A for other applications (not investigated by UL)
12 VDC, 1.0 A maximum. Includes 110 mA for each control center connected to the
system, and up to 400 mA for the programmable outputs.
85 mA standby; 160 mA alarm with all outputs activated
12 VDC nominal (11.2 VDC to 12.3 VDC)
The control panel stops processing point faults when the voltage drops below
9.5 VDC.
•
D126 (7 Ah) or D1218 (18 Ah) sealed, lead acid rechargeable
•
1.7 A maximum recharging current
•
Low battery condition occurs when battery drops below 12 VDC
•
If AC power fails and the battery drops below 9.5 VDC, the control panel stops
processing point faults. Disconnect the battery under these conditions.
•
Maximum auxiliary current to recharge standby battery within 72 hours:
-
12 V, 7 Ah Battery: 400 mA
-
12 V, 18 Ah Battery: 900 mA
•
AC Input Voltage: 100 VAC to 240 VAC
•
Line Voltage Frequency: 47 Hz to 63 Hz
•
Maximum Input Current: 0.5 A
•
Power Factor: Approximately 0.65 at full load
•
Nominal Output Voltage under AC line input: 18 VDC
•
Output Voltage Range under AC line input: 16 VDC to 20 VDC
•
Continuous Rated Output Current: 1.25 A
•
Output Current Limit: Approximately 1.75 A to 2.5 A
•
Periodic and Random Deviation (PARD): Less than 250 mV
8 VDC to 14 VDC
35 mA standby; 135 mA maximum with connected accessories
100 mA, 12 VDC supervised output for accessories
0.8 mm (#22 AWG) to 1.8 mm (#14 AWG)
•
Control panel to DX2010 (DX2010 auxiliary output not used):
0.8 mm (#22 AWG) = 305 m (1000 ft)
-
1.2 mm (#1.2 mm) = 610 m (2000 ft)
-
•
Control panel to DX2010 (DX2010 auxiliary output supplying 100 mA):
0.8 mm (#22 AWG) = 30 m (100 ft)
-
1.2 mm (#1.2 mm) = 76 m (250 ft)
-
+0°C to +50°C (+32°F to +122°F)
5% to 85% @ +30°C (+86°F)
60 Ω maximum
Up to eight inputs; input contacts can be normally open (NO) or normally closed
(NC) with appropriate EOL resistors for supervision.
75