Texecom Premier 24 Installation Manual page 63

Premier 24 Installation Manual
The plug-on digimodem can be programmed with up to 2
sets of Alarm Receiving Centre (ARC) information. Each
'Set' consists of the following options:
Protocol
This is the reporting protocol that is used to communicate
with the Alarm Receiving Centre. The following 4 protocols
are supported:
•
Fast Format: The panel will report using Fast Format.
If this option is selected the 'Reporting Channels'
must be programmed (see below)
•
Contact ID: The panel will report using Contact ID.
•
SIA Level II: The panel will report using SIA Level II
•
SMS Messaging: The panel will send Short Message
Service (SMS) text messages to a mobile phone
Primary Telephone Number
This is the first telephone number that the digimodem will
dial for the Alarm Receiving Centre or the first mobile
telephone number to send SMS to. This telephone number
can be up to 24 digits.
When entering telephone
repeatedly will allow the following characters to be selected:
,
(3 second pause)W(10 second pause)+R(recall signal).
!#
Secondary Telephone Number
This is the second telephone number that the digimodem
will dial for the Alarm Receiving Centre or the second
mobile telephone number to send SMS to. This telephone
number can be up to 24 digits.
Account Number
This is the account number that will be reported to the
Alarm Receiving Centre. Each account number can be up
to 6 digits.
Dialling Attempts
This is the number of times the digimodem will try to dial the
Alarm Receiving Centre or Pager telephone number.
!
The number of dialling attempts is limited to 9. If this
value is set to 0, the digimodem will never dial out.
The following option is only displayed if the
Fast Format protocol is selected
Reporting on
This option defines which channels report to the selected
Alarm Receiving Centre.
Restoring on
This option defines which channels report a restore to the
selected Alarm Receiving Centre.
Open/Close on
This option defines which channels report Open/Close to the
selected Alarm Receiving Centre.
INS248
numbers, pressing
5
Programming the Control Panel
The following option is only displayed if Contact ID,
SIA Level II or EasyCom Pager protocols are selected
Reports
This option defines which events report to the Alarm
Receiving Centre when using Contact ID or SIA Level II. The
following options are available:
P - Priority Alarm and Cancel Events
The system will report Priority alarm and cancel events to
the selected Alarm Receiving Centre.
A - Normal Alarm and Cancel Events
The system will report alarm and cancel events to the
selected Alarm Receiving Centre.
O - Open and Close Events
The system will report open and close events to the
selected Alarm Receiving Centre.
O - Omit and Reinstate Events
The system will report omit and reinstate events to the
selected Alarm Receiving Centre.
M - Maintenance Alarm Events
The system will report maintenance alarm events to the
selected Alarm Receiving Centre.
T - Tamper Alarm Events
The system will report tamper alarm events to the
selected Alarm Receiving Centre.
C - Test Call Events
The system will report test call events to the selected
Alarm Receiving Centre.
R - Restore Events
The system will report restore events to the selected
Alarm Receiving Centre.
The following option is only displayed if Fast Format
Contact ID or SIA Level II protocols are selected
Config.
This option defines which secondary options are enabled.
The following options are available:
D - Disable Zone Res
The system will NOT report zone restore events to the
selected Alarm Receiving Centre.
S - SIA Level I
The system will report events to the selected Alarm
Receiving Centre using SIA Level I.
R - Enable Radio-Pad
The system will use the Paknet radio-pad to report events
to the selected Alarm Receiving Centre.
G - Enable ComGSM
The system will use the ComGSM to report events to the
selected Alarm Receiving Centre (see page 6 for details).
F - Use GSM First
The ComGSM is the primary path when it is enabled
63