Function Setting List - JUKI DDL-8700A-7 Instruction Manual

7. Function setting list

No. Item
 Soft start The number of sttches to be sewn at a low speed when the soft-
functon start functon s used at the start of sewng.
0 : The functon s not selected.
 to 9 : The number of sttches to be sewn under the soft-
2 Materal end Materal end sensor functon.
sensor functon 0 : Materal end detecton functon s not operatve.
 : After detectng materal end, the specfed number of
3 Thread trmmng Thread trmmng functon by materal end sensor.
functon by 0 : Automatc thread trmmng functon after detecton of ma-
materal end
sensor  : After detectng materal end, the specfed number of
4 Number of Number of sttches for materal end sensor.
sttches for Number of sttches from detecton of materal end to stop of the
materal end sewng machne.
sensor
5 Flcker reducng Flcker reducng functon
functon
0 : Flcker reducng functon s not operatve.
 : Flcker reducng functon s effectve
6 Bobbn thread Bobbn thread countng functon
countng
0 : Bobbn thread countng functon s not operatve.
functon
 : Bobbn thread countng functon s operatve.
7 Unt of bobbn Unt of bobbn thread countng down
thread countng 0 :  Count/0 sttches
*
down  :  Count/5 sttches
2 :  Count/20 sttches
3 :  Count/thread trmmng
8 Number of Sewng speed of reverse feed sttchng
rotaton of
*
reverse feed
sttchng
9 Thread Thread trmmng prohbtng functon.
trmmng
0 : Thread trmmng s effectve.
prohbtng
 : Thread trmmng s prohbted.
functon
0 Settng of Poston of needle bar s specfed when the sewng machne
needle bar stop stops.
poston when 0: The needle bar stops at ts lower poston.
the sewng : The needle bar stops at ts upper poston.
machne stops.
 Operaton Operation confirmation sound for operation panel
confirmation
0 : Operation confirmation sound is not generated
sound for
1 : Operation confirmation sound is generated.
operaton panel
2 Optnal swtch Swtchng of functon of optonal swtch.
functon
selecton
3 Functon of Functon of prohbtng start of the sewng machne by bobbn thread countng
prohbtng start
0 : When countng s out (- or less) Functon of prohbtng
of the sewng
machne by
 : When countng s out (- or less) Functon of prohbtng
*
bobbn thread
counter
2 : When countng s out (- or less), the sewng machne
4 Sewng counter Countng functon of sewng (number of completon of process)
0 : Sewng counter functon s not operatve.
 : Sewng counter functon s operatve. (Every tme thread
2 : Wth the sewng countng swtch nput functon
5 Thread wpng Thread wiping operation after thread trimming is specified.
functon after 0 : Thread wpng s not carred out after thread trmmng
thread trmmng  : Thread wpng s carred out after thread trmmng
2 Functon of Functon of lftng presser foot when the pedal s n neutral pos-
automatc ton.
presser foot 0 : Functon of neutral automatc presser lftng s not opera-
lftng at pedal's
neutral poston  : Selecton of functon of neutral presser lftng.
* Do not change the set values with asterisk (*) mark as they are functions for maintenance. If the standard set value set at the
time of delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated.
If it is necessary to change the set value, please purchase the Engineer's Manual and follow the instructions.
Descrpton
start mode.
sttches (No. 4) wll be sewn, and the sewng machne wll
stop.
teral end s not operatve.
sttches (No. 4) wll be sewn, and the sewng machne wll
stop and perform automatc thread trmmng.
(Output of solenod s prohbted. : Thread trmmer and wper)
start of the sewng machne s not operatve.
start of the sewng machne after thread trmmng s op-
eratve.
stops once. Functon of prohbtng start of the sewng
machne after thread trmmng s operatve.
trmmng s performed)
tve.
Settng range
0 to 9
(Sttches)
0/
0/
0 to 9
(Sttches)
0/
0/
0 to 3
50 to 3,000
(st/mn)
0/
0/
0/
0 to 2
0 to 2
0/
0/
– 29 –
Indcaton of functon settng Ref. page
1 0
33
2 0
33
3 0
33
4 5
33
5 0
33
6 1
33
7 0
8 1 9 0 0
9 0
33
1 0 0
33
1 1 1
33
1 2 o P t _
34
1 3 0
1 4 1
37
1 5 1
2 1 0
37