JUKI DDL-8700A-7 Instruction Manual page 35

No. Item
Pedal curve s selected. (Improvng pedal nchng operaton)
87 Functon of pedal
curve selecton
Number of rotations
Automatc UP stop functon s set mmedately after turnng ON the
90 Intal moton up
power.
stop functon
0 : off
 : on
9 Functon of prohbtng It s effectve n combnaton wth the machne head provded
compensaton wth tenson release functon.
operaton after turnng 0 : Tenson release functon s neffectve.
handwheel by hand  : Tenson release functon s effectve.
92 Functon of Functon to reduce speed at the tme of completon of reverse
reducng speed feed sttchng at the start of sewng.
of reverse feed 0 : Speed s not reduced.
sttchng at the  : Speed s reduced.
start of sewng
93 Functon added to Operaton of needle up/down compensatng swtch s changed
needle up/down after turnng ON the power or thread trmmng.
compensatng 0 : Normal (needle up/down compensatng sttchng only)
swtch  : One sttch compensatng sttchng s performed only when
94 Continuous + The functon that does not stop the sewng machne by com-
One-shot nonstop bnng contnuous sttchng wth one-shot sttchng usng the
functon
program sewng functon whch s avalable n the IT operaton
panel.
0 : Normal (The sewng machne stops when a step s com-
 : The sewng machne does not stop when a step s com-
95 Head selecton Machne head to be used s selected.
functon (When the machne head s changed, each settng tem s changed
to the ntal value of the machne head.)
96 Max. number of Max. number of rotaton of the sewng machne head can be set.
rotaton settng (The MAX value dffers by machne head.)
00 Number of Sets the number of sttches to be sewn at the begnnng of sew-
sttches sewn
ng before the thread clamp solenod (CN36-7) starts operatng
before thread
0: Thread clamp solenod does not operate.
clamp works at
-9: The number of sttches to be sewn before the thread clamp
the begnnng of
solenod operates
sewng
03 Needle cooler Delay tme from the stop of sewng machne to the output OFF s
output OFF specified using the needle cooler output function.
delay tme
09 LED lght Used to adjust brghtness of the LED lght
dmmer utlty 0: Output OFF
settng
20 Man shaft Man shaft reference angle s compensated.
reference angle
compensaton
2 Up poston Angle to detect UP poston startng s compensated.
startng angle
compensaton
22 DOWN poston Angle to detect DOWN poston startng s compensated.
startng angle
compensaton
24 Settng of Settng to reduce the power consumpton whle the sewng ma-
energy-savng chne s n standby state
functon durng 0: Energy-savng mode s neffectve
standby : Energy-savng mode s effectve
* Do not change the set values with asterisk (*) mark as they are functions for maintenance. If the standard set value set at the
time of delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated.
If it is necessary to change the set value, please purchase the Engineer's Manual and follow the instructions.
Descrpton
2
0
aforementoned changeover s made. (Upper stop / up-
per stop)
pleted.)
pleted and proceeds to next step.
Settng range
0//2
1
Pedal stroke
0/
0/
0/
0/
0/
50 to MAX
(st/mn)
0-9
(sttches)
00 to
2000 ms
0 to 00%
–60 to 60
–5 to 5
–5 to 5
0/
– 32 –
Indcaton of functon settng Ref. page
8 7 0
4
9 0 1
42
9 1 1
9 2 0
4
9 3 0
42
9 4 0
42
9 5 8 7 a S
9 6 4 0 0 0
42
1 0 0 0
1 0 3 5 0 0
1 0 9 1 0 0
42
1 2 0 – 1 3
42
1 2 1 5
42
1 2 2 0
42
1 2 4 0
42