JUKI DDL-8700A-7 Instruction Manual page 33

No. Item
22 Needle up/down Functon of the needle up/down correcton swtch s changed
correcton over.
swtch 0 : Needle up/down compensaton
changeover  : One sttch compensaton
functon
25 Thread trmmng Thread trmmng operaton after movng the needle away from
operaton after ts upper or lower poston by turnng the handwheel by hand s
turnng the specified.
handwheel by 0 : Thread trmmng operaton s carred out after turnng the
han
 : Thread trmmng operaton s not carred out after turnng
29 Settng of one- Ths functon sets the sucton tme of ntal moton of back-tack
touch type solenod.
reverse feed
solenod pull-n
tme
30 Functon of Functon of reverse feed sttchng on the way
reverse feed 0 : Normal one-touch type reverse feed sttchng functon
sttchng on the  : Functon of reverse feed sttchng on the way s operatve.
way
3 Number of Number of sttches of reverse feed sttchng on the way.
sttches of reverse
feed sttchng on
the way
32 Effectve Effectve condton of reverse feed sttchng on the way
condton of 0 : Functon s not operatve when the sewng machne stops.
reverse feed  : Functon s operatve when the sewng machne stops.
sttchng on the
way when the
sewng machne
s stoppng.
33 Thread trmmng Thread trmmng functon by reverse feed sttchng on the way
functon by 0 : Automatc thread trmmng functon after completon of
reverse feed
sttchng on the  : Automatc thread trmmng after completon of reverse
way
35 Number of Lowest speed by pedal
*
rotaton at a low (The MAX value dffers by machne head.)
speed
36 Number of Thread trmmng speed
*
rotaton of (The MAX value dffers by machne head.)
thread trmmng
37 Number of Sewng speed at the start of sewng (soft-start)
rotaton of soft- (The MAX value dffers by machne head.)
start
38 One-shot speed One-shot speed (The max. value depends on the number of ro-
taton of the sewng machne head.)
39 Pedal stroke Poston where the sewng machne starts rotatng from pedal
*
at the start of neutral poston (Pedal stroke)
rotaton
40 Low speed Poston where the sewng machne starts acceleratng from
*
secton of pedal pedal neutral poston (Pedal stroke)
4 Startng poston Poston where the cloth presser starts lftng from pedal neutral
*
of lftng presser poston (Pedal stroke)
foot by pedal
42 Startng poston Startng poston of lowerng presser foot
*
of lowerng Stroke from the neutral poston
presser foot
43 Pedal stroke 2 for Poston 2 where the thread trmmng starts from pedal neutral
startng thread poston (When the functon of lftng presser foot by pedal s pro-
*
trmmng vded.) (Pedal stroke)
(Effectve only when Item No. 50 s set at .)
44 Pedal stroke Poston where the sewng machne reaches ts hghest sewng
for reachng the speed from pedal neutral poston (Pedal stroke)
*
maxmum number
of rotaton
45 Compensaton of Compensaton value of the pedal sensor
*
neutral pont of
the pedal
47 Auto-lfter Lmtaton tme of watng for lftng solenod type auto-lfter de-
selectng functon vce
48 Pedal stroke  for Poston where thread trmmng starts from pedal neutral poston
*
startng thread (Standard pedal) (Pedal stroke)
trmmng (Effectve only when Item No. 50 s set at 0.)
49 Lowerng tme of Sets the tme requred untl the lowerng of the presser foot s
presser foot completed after a depress on the pedal
* Do not change the set values with asterisk (*) mark as they are functions for maintenance. If the standard set value set at the
time of delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated.
If it is necessary to change the set value, please purchase the Engineer's Manual and follow the instructions.
Descrpton
handwheel by hand
the handwheel by hand
50 ms to 500 ms
reverse feed sttchng on the way s not operatve.
feed sttchng on the way s performed.
Settng range
0/
0/
50 to 500
(ms)
0/
0 to 9
(Sttches)
0/
0/
50 to MAX
(st/mn)
00 to MAX
(st/mn)
00 to MAX
(st/mn)
50 to MAX
(st/mn)
0 to 50
(0. mm)
0 to 00
(0. mm)
– 60 to –0
(0.mm)
8 to 50
(0. mm)
– 60 to –0
(0. mm)
0 to 50
(0. mm)
–5 to 5
0 to 600
(second)
– 60
to – 0
(0. mm)
0
to 500
(0 ms)
– 30 –
Indcaton of functon settng Ref. page
2 2 0
37
2 5 1
2 9 2 5 0
37
3 0 0
38
3 1 4
38
3 2 0
38
3 3 0
38
3 5 2 0 0
3 6 3 0 0
3 7 8 0 0
33
3 8 2 5 0 0
38
3 9 3 0
4 0 6 0
4 1 – 2 1
4 2 1 0
4 3 – 5 1
4 4 1 5 0
4 5 0
4 7 6 0
39
4 8 – 3 5
4 9 1 4 0
4