JUKI DDL-8700A-7 Instruction Manual page 38

Input function list
Functon Abbreva-
code ton
0 noP No functon
 HS Needle up / down compensatng
sttchng
2 bHS Back compensatng sttchng
3 EbT Functon of cancelng once re-
verse feed sttchng at the end of
sewng
4 TSW Thread trmmng functon
5 FL Presser foot lftng functon
6 oHS One sttch compensatng sttchng
7 SEbT Functon of cancel of reverse feed
sttchng at start/end
8 PnFL Presser lftng functon when pedal
s neutral
9 Ed Materal edge sensor nput
0 LnH Functon of prohbtng depressng
front part of pedal
 TnH Functon of prohbtng thread
trmmng output
2 LSSW Low speed command nput
3 HSSW Hgh speed command nput
4 USW Needle lftng functon
5 bT Reverse feed sttchng swtch n-
put
6 SoFT Soft start swtch nput
oSSW
7 One-shot speed command swtch
nput
bKoS
8 Backward one-shot speed com-
mand swtch nput
SFSW
9 Safety swtch nput
MES
20 Thread trmmng safety swtch n-
put
AUbT
2 Automatc reverse feed sttchng
cancellaton/addton swtch
CUnT
22 Sewng counter nput
23 Tn Tsw command prohbton nput
24 USTP Lsw command prohbton/needle-
up stop nput
Functon tem
– 35 –
Remarks
(Standard settng)
Every tme the swtch s pressed, normal feed sttchng
by half sttch s performed. (Same operaton as that of up
/ down compensatng sttchng swtch on the panel.)
Reverse feed sttchng s performed at low speed whle the
swtch s held pressng.
By depressng the back part of the pedal after pressng
the swtch, operaton of reverse feed sttchng s can-
celed once.
Ths functon s actuated as the thread trmmng swtch.
Ths functon s actuated as the foot lfter swtch.
Every tme the swtch s pressed, one sttch sttchng op-
eraton s executed.
By operatng the optonal swtch, neffectve/effectve can
be alternately changed over.
Every tme the swtch s pressed, the functon whether
automatcally lftng the presser foot when the pedal s
neutral or not can be selected.
Ths functon works as the nput sgnal of materal edge sensor.
Rotaton by pedal s prohbted.
Output of thread trmmng s prohbted.
Ths functon works as low speed swtch for standng
sewng machne.
Ths functon works as hgh speed swtch for standng
sewng machne.
UP stop moton s performed when swtch s pressed dur-
ng DOWN stop.
Reverse feed sttchng s output as long as the swtch s
held pressed.
The speed of sttch s lmted to the predetermned soft-
start speed as long as the swtch s held pressed.
Ths functon works as one-shot speed command as long
as the swtch s pressed.
Reverse feed sttchng s performed n accordance wth
the one-shot speed command as long as the swtch s
held pressed.
Rotaton s prohbted.
It operates as an nput sgnal of the thread trmmer safety
swtch.
Every tme the swtch s pressed, reverse feed sttchng
at sewng start or reverse feed sttchng at sewng end s
cancelled or added.
Every tme the swtch s pressed, the sewng counter
value s ncreased.
Thread trmmng command s prohbted.
Sewng by means of the pedal swtch s prohbted.
The sewng machne stops wth ts needle up durng
sewng.