JUKI DDL-8700A-7 Instruction Manual page 43

!7 Foot lift function after thread trimming (Function setting No. 55)
Ths functon can automatcally lft the presser foot after thread trmmng. Ths functon s effectve only when
t s used n combnaton wth the AK devce.
5 5
!8 reverse revolution to lift the needle after thread trimming (Function setting No. 56)
Ths functon s used to make the sewng machne rotate n the reverse drecton after thread trmmng to lft
the needle bar almost to hghest poston. Use ths functon when the needle appears under the presser foot
and t s lkely to make scratches on the sewng products of heavy-weght materal or the lke.
5 6
(caution) the needle bar is raised, by rotating the machine in the reverse direction, almost to the high-
est dead point. this may result in slip-off of the needle thread. It is therefore necessary to
adjust the length of thread remaining after thread trimming properly.
!9 Function of holding predetermined upper / lower position of the needle bar (Function setting No. 58)
When the needle bar s n the upper poston or n the lower poston, ths functon holds the needle bar by ap-
plyng a brake slghtly.
5 8
@0 change-over function of auto / Pedal for sewing speed of the reverse feed stitching at the start
of sewing (Function setting No. 59)
Ths functon selects whether the reverse feed sttchng at the start of sewng s performed wthout a break at
the speed set by the functon settng No. 8 or the sttchng s performed at the speed by the pedal operaton.
5 9
(caution)
1. the max. sewing speed of the reverse feed stitching at the start of sewing is limited to the speed set
by the function setting No. 8 regardless of the pedal.
2. When "0" is selected, stitches of reverse feed stitching may not match those of normal feed stitching.
@1 Function of stop immediately after the reverse feed stitching at the start of sewing (Function setting No. 60)
Ths functon temporarly stops the sewng machne even when keepng depressng the front part of the pedal at the
tme of completon of process of reverse feed sttchng at the start of sewng.
It s used when sewng a short length by reverse feed sttchng at the start of sewng.
6 0
0 : Not provded wth the functon of temporary stop of the
sewng machne mmedately after the reverse feed
sttchng at the start of sewng
 : Provded wth the functon of temporary stop of the
sewng machne mmedately after the reverse feed
sttchng at the start of sewng
0 : off Functon of automatcally lftng the presser foot s not provded.
1
(Presser foot does not automatcally go up after thread trmmng.)
 : on Functon of automatcally lftng the presser foot s provded.
(Presser foot automatcally goes up after thread trmmng.)
0 : off Functon of makng the sewng machne rotate n the reverse drec-
0
ton to lft the needle after thread trmmng s not provded.
 : on Functon of makng the sewng machne rotate n the reverse drec-
ton to lft the needle after thread trmmng s provded.
0 : off Not provded wth the functon of holdng predetermned upper/low-
0
er poston of the needle bar
 : on Provded wth the functon of holdng predetermned upper/lower
poston of the needle bar (holdng force s weak.)
2 : on Provded wth the functon of holdng predetermned upper/lower
poston of the needle bar (holdng force s medum.)
3 : on Provded wth the functon of holdng predetermned upper/lower
poston of the needle bar (holdng force s strong.)
0 : Manual The speed s ndcated by the pedal operaton.
1
1 : Auto Automatic stitching at the specified speed
0
– 40 –
Stop the sewing machine
temporarily to change
direction of sewing products.