Extron electronics DMP 128 User Manual page 150

command and response table for DsP sis commands (continued)
command
audio group master commands
notEs: • See Group masters
• A group must have assigned members for these commands to have an effect.
X6^
• For , a positive (+) value is assumed unless a negative (-) value is specified.
X6^
• If entering a
"invalid parameter" (E13) error.
X6^ X6& X6*
• , , and
Set a group fader control
Example:
Raise a group fader control
Example:
Lower a group fader control
View the group fader control
level
Mute a group mute control
Clear (unmute) a group
mute control
View a group mute control
Set soft limits
Example:
View soft limits
View group type
View group members
X6)
notEs: = Gain and trim control
X6%
= Group master group number
X6^
= Group fader level
X6&
= Group fader increase/decrease
X6*
= Group fader soft limit
X6(
= Group type
ascii command
(host to device)
,
for more information about audio group masters.
value outside the valid range for the group or outside the soft limits, the DMP 128 responds with an
values can be sent without leading zeroes; responses are always 5 digits.
E X6% X6^ }
D * GRPM
E }
d2*-293*GRPM
E X6% X6& }
D * +GRPM
E }
d2*30+GRPM
E X6% X6& }
D * -GRPM
E X6% }
D GRPM
E X6% }
D *1GRPM
E X6% }
D *0GRPM
E X6% }
D GRPM
E X6% X6* X6*
L GRPM
* upper * lower
E }
L2 * +60 * -60GRPM
E X6% }
L GRPM
E X6% }
P GRPM
E X6% }
O GRPM
See table 1 on page 144
01 - 32
dB value, in 0.1 dB increments, using negative numbers and eliminating
decimal places using a 10x multiplier. – 100.0 dB to +80.0 dB is
represented by – 1000 to 800.
The valid range depends on the type of gain or trim block assigned
to the group number (
dB value, in 0.1 dB increments, to raise or lower a group fader.
dB value, in 0.1 dB increments. The valid range must be within the
range for the gain block grouped in
6 = gain
12 = mute
response
(device to host)
X6% X6^]
GrpmD *
]
GrpmD02*-00293
X6% X6^]
GrpmD *
]
GrpmD02*-00263
X6% X6^]
GrpmD *
X6% X6^]
GrpmD *
X6% ]
GrpmD *+00001
X6% ]
GrpmD *+00000
X6% X6$]
GrpmD *
}
X6% X6* X6*]
GrpmL * *
]
GrpmL02*+00060*-00060
X6% X6* X6*]
GrpmL * *
X6% X6(]
GrpmP *
X6% X6) X6)
GrpmO * * *
1 2
X6) ]
*
16
...
X6%
).
X6%
DMP 128 • SIS Programming and Control
additional
description
Set a group fader to a value
X6^
of .
Set the group 2 fader control
to -29.3 dB.
X6%
Increase the level of the
X6&
group fader by dB.
Raise the group 2 fader 3 dB
(from -29.3 dB to -26.3 dB,
starting from the level set
in the "Set a group fader
control" example, above.
X6%
Decrease the level of the
X6&
group fader by dB.
In verbose modes 1 and 2, the
response is simplified to
X6^]
.
X6%
Mute all blocks in group .
Umute all blocks in group
X6%
.
X6$
For group masters,
is always expressed as a
positive or negative 5-digit
value.
Set the groups soft limits to
X6* X6*
and .
Set the upper soft limit for the
group 2 fader to +6.0 dB and
the lower limit to -6.0 dB.
In verbose modes 0 and 1,
the response is simplified to
X6* X6*]
* .
X6(
Show the group type ( )
X6%
for group . In verbose
modes 0 and 1, the response
X6(]
is simplified to .
X6)
is the control address.
In verbose modes 0 and 1,
the response is simplified to
X6) X6) X6) ]
* *...* .
1 2 16
.
144