Extron electronics ProDSP DMP 128 Setup Manual

DMP 128 • Setup Guide
Disconnect Power and Mount the DMP 128
Disconnect power to the DMP 128 and turn off all devices that will be connected to it. The DMP 128 is housed in a full rack width,
8.5 inch deep, 1U high metal enclosure that can sit on a table with the provided rubber feet or can be rack mounted. Select a
suitable mounting location, then choose an appropriate mounting option.
Make all external device connections before applying power.
DMP 128 C P AT
1 2
100-240V ~ 0.6A MAX
MIC/LINE INPU T S MIC/LINE INPUTS
100-240 ~ 0. 6 A 100-240 ~ 0.6A
1 1 2 2
MIC +48V
1 2 3 4
5 6
MIC MIC
+48V + 48V
5 5 6 6
1 1 2 2 3 3 4 4
5 5 5 6 6 6 7 7 7 8 8 8
50/60 Hz
50/60 HZ 50/60 HZ
Connections
a
AC Power — IEC power connector 100 – 240 VAC, 50 – 60 Hz.
b
Phantom power indicators — Green LEDs light when + 48 V phantom power is placed on the corresponding input. Phantom
power voltage is not adjustable and is available only on inputs 1 – 8.
c
Mic/Line 1-8 input connectors — Connect up to eight balanced or
unbalanced microphone or mono line level devices using 3-pole 3.5 mm
captive screw connectors. Phantom power is available to any of these
inputs. Wire as shown at right.
d
Mic/Line 9-12 input connectors — Connect up to four balanced or unbalanced
mono microphone or line level, or two stereo devices to these 6-pole 3.5 mm
captive screw connectors (see Audio Input Wiring at right).
NOTES:
•
Balanced or unbalanced stereo devices can be connected to the 6-pole
connectors.
•
When using the 5-pole CSR adapter, connect it so that the far left plug inserts
into the far left jack of the 6-pole input connector (see example at right).
e
Mono output connectors — Connect up to eight balanced
or unbalanced mono line level or four stereo outputs to these
6-pole 3.5 mm captive screw connectors. Wire as shown at
right. In addition 5- and 6-pole connectors can be used (see
Audio Output Wiring, right).
This guide provides basic instructions for an experienced technician to install
the DMP 128 ProDSP
and specifications, see the DMP 128 product page at www.extron.com.
3 4 9 10 DMP 128 C P AT
DMP 12 8 C P AT DMP 128 C P AT
3 3 4 4 9 9 10 10
LINE
LIN E LIN E PHONE PHON E
7 8 11 12
7 7 8 8 11 11 12 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Matrix Processor. For additional information
™
1 2 3 4
DIGI T A L I/O DIGI T A L I/O
1 1 2 2 3 3 4 4
O O
1 2 3 4 5 G
PHONE
U U
1 2 3 4 5 1 2 3 4 5
T T
P P
5 6 7 8
U U
11 12 13 14 15 11 12 13 14 15
5 5 6 6 7 7 8 8
T T
S S
11 12 13 14 15 G
Tip
Ring
Sleeve
Balanced Input
Tip
Ring
Sleeve Tip
Ring
Balanced Input
Sleeve
Balanced Output
Tip
Ring
Sleeve
Balanced Output
ATTENTION:
the sleeves to the ground contact.
DO NOT connect the sleeves to the negative (-) contacts.
Product Category
6 7 8 9 10 G
1 2 3
6 7 8 9 10 6 7 8 9 10 1 1 1 2 2 2 3 3 3 4 4 4
EXP EXP LAN LAN
RS-232
16 17 18 19 20 16 17 18 19 20
RS-2 32 RS-232
RESET RESET
16 17 18 19 20 G Tx Rx G EXP LAN
Tx T T Rx TxRx
Audio Input Wiring
Tip
Sleeve
1 0 Unbalanced Input
0 - 2
4 0
V ~
- - A
M A
X
1
M I
C
5 0 1
/ 6 0 + 4
H z 8 V
2
2
3
4
5
3
6
5
7
8
6
Audio Input Wiring
7
Audio Output Wiring Tip
Sleeve
Tip
NO Ground Here
Unbalanced Input
Sleeve
5-pole CSR
Unbalanced Output
Audio Output Wiring
Tip
NO Ground Here
Sleeve
Unbalanced Output
For unbalanced audio outputs, connect
4
RESET
DO NOT
4
Connect Here
9
1 0
8
D M
P 1
2 8
1 1
1 2
1