Advertisement
Quick Links
IPCP 505 • Setup Guide
The Extron IPCP 505 IP Link
control, monitor, and troubleshoot AV equipment, including display devices and switchers. It includes an embedded web server,
multiple bidirectional serial ports, switched low voltage power output ports, relays, and configurable flex I/O ports for use in
applications that require control and monitoring of multiple devices within a large-scale AV system.
The IPCP 505 is configured using the free Extron Global Configurator (GC) software. The IPCP 505 integrates seamlessly with
Extron GlobalViewer
Enterprise (GVE) software and the free GlobalViewer web-based AV resource management for remote
®
control applications. The IPCP 505 supports multiple TouchLink
Configurator and other useful software applications are available at www.extron.com.
Front Panel Features
Switched
12 VDC LEDs
IPCP 505
SWITCHED
12VDC
1
2
LIMIT
R
3
4
Power LED
Reset Button
(recessed)
Rear Panel Features
COM1 - COM6
Rear Panel
100-240V
50-60Hz
1
2
COM1
+ - + -
TX RX G
SWITCHED 12VDC
40W MAX TOTAL
3
4
COM4
+ - + -
TX RX G
5A MAX
Power
Switched 12 VDC
Input
Power Output
Control Processor integrates Ethernet connection into AV systems to allow users to remotely
®
COM (Serial) LEDs
IR/Serial LEDs
COM
RTS
CTS
1
TX
TX
RX
RX
OVER
1
2
3
4
5
6
7
8
5
COM7, COM8
IR/Serial
(RS-232)
(RS-232, RS-422, RS-485)
COM2
COM3
COM7
1
2
S G S G
TX RX
G
TX RX
G
TX RX
G
RTS
CTS
IR/SERIAL
COM5
COM6
COM8
5
6
TX RX
G
TX RX
G
TX RX
G
RTS
CTS
S G S G
touchpanel interfaces over a standard Ethernet network. Global
®
Flex I/O LEDs
FLEX
IR/S
RELAY
I/O
2
3
4
1
2
3
4
1
2
6
7
8
5
6
7
8
3
4
Relay LEDs
Relays
3
4
1
2
3
4
S G S G
RELAY
7
8
5
6
7
8
FLEX I/O
S G S G
1 2 3 4 G
Flex I/O
(digital
input/output,
analog input)
100
LAN/
Network
LINK
LEDs
IR
ACT
IR Receiver
MAC
LAN
Address
Ethernet
(LAN)
1
Advertisement
Related Manuals for Extron electronics IPCP 505
Summary of Contents for Extron electronics IPCP 505
-
Page 1: Front Panel Features
Extron GlobalViewer Enterprise (GVE) software and the free GlobalViewer web-based AV resource management for remote ® control applications. The IPCP 505 supports multiple TouchLink touchpanel interfaces over a standard Ethernet network. Global ® Configurator and other useful software applications are available at www.extron.com. -
Page 2: Cabling And Features
IPCP 505 • Setup Guide (Continued) Cabling and Features Attach cables using the following wiring diagrams as a guide. Full details are available in the IPCP 505 User Guide. ATTENTION: Installation and service must be performed by authorized personnel only. Power Power Input •... -
Page 3: Control - Ir/Serial
Control — IR/Serial IR/Serial Ports Output options: Rear Panel Front Panel • IR (with or without carrier signals) • unidirectional RS-232 COM7 S G S G S G S G TX RX IR/S RELAY IR/SERIAL COM8 TX RX S G S G S G S G IR/S LEDs Light when signals are transmitted... -
Page 4: Control - Lan (Ethernet)
IPCP 505 • Setup Guide (Continued) Control — LAN (Ethernet) LAN (Ethernet) Connect to an Ethernet network with a straight-through cable. This port must be con gured. Rear Panel Front Panel Default protocol: • IPCP IP address: 192.168.254.254 Address • Gateway IP address: 0.0.0.0 •... -
Page 5: Obtaining Control Drivers
Obtain IP address and subnet mask information for the IPCP from the network administrator. Cabling and Features Cable devices to the IPCP 505 (see on page 2), connect touchpanels to the same network as the IPCP, then power on all the devices. Connect the IPCP to a network, power it on, and use ARP (see Network Configuration Using ARP below) to set the... -
Page 6: Setup Checklist: How To Proceed With Installation
(Inside India Only) Extron USA - West Extron USA - East +31.33.453.4040 +91.80.3055.3777 +1.714.491.1500 +1.919.850.1000 +31.33.453.4050 FAX +91.80.3055.3737 FAX +1.714.491.1517 FAX +1.919.850.1001 FAX © 2013 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com...