Download  Print this page

Advertisement

Advertisement

Table of Contents

   Summary of Contents for Ducati Multistrada 1200 ABS

  • Page 2 Owner’s manual...
  • Page 4 Ducati motorcycle. We think you Ducati Motor Holding S.p.A. cannot accept any liability will ride your Ducati motorcycle for long journeys as well as for errors that may have occurred in the preparation of this short daily trips. Ducati Motor Holding S.p.A. wishes you manual.
  • Page 5: Table Of Contents

    Battery voltage indicator (BATTERY) 50 Clock 19 “Riding Style” customisation 52 Fuel level indicator 20 DTC (Ducati Traction Control) setting function 54 Coolant temperature 21 ENGINE setting function (Engine Power Control) 58 Total distance covered indicator: “Odometer“ 22 DES setting function (Ducati Electronic Suspension) 60 “Trip 1“...
  • Page 6 LAP registration function 74 Side stand 122 Stored LAP display function 76 Power outlet 123 DTC (Ducati Traction Control) on/off function 78 Adjusting the front fork 124 Digital RPM indication function 80 Adjusting the rear shock absorber 126 Clock setting function 82 Motorcycle setup variation (”S”...
  • Page 7 Chain lubrication 152 Wheels 175 Replacing the high and low beam bulbs 153 Tyres 175 Rear turn signals 155 Suspensions 175 Number plate light 156 Exhaust system 176 Beam setting 156 Colour schemes 176 Rear-view mirror adjustment 158 Electric system 176 Tubeless tyres 159 Checking engine oil level 161 Scheduled maintenance reminder 183...
  • Page 8: General Indications

    Ducati Dealer or Authorised Service Centre. The information contained herein will prove useful on your trips - and Ducati Motor Holding S.p.A. wishes you smooth, enjoyable riding - and will help you keep the performance of your motorcycle unchanged for a long time.
  • Page 9 Useful information for safe riding Be very careful at road junctions, or when riding in areas near exits from private land or car parks, or on the slip roads to motorways. Warning ALWAYS turn off the engine when refuelling. Read this section before riding your motorcycle. Be extremely careful not to spill fuel on the engine or on the exhaust pipe when refuelling.
  • Page 10: Useful Information For Safe Riding

    If the side panniers are fitted (available upon request from The total weight of the motorcycle in running order the Ducati spare parts service), divide the baggage and including rider, passenger, luggage and additional accessories based on their weight and place them uniformly accessories should not exceed: inside the side panniers.
  • Page 11: Identification Data

    Identification data All Ducati motorcycles have two identification numbers, for frame (fig. 1) and engine (fig. 2). Frame number Engine number Note These numbers indicate the motorcycle model and should be quoted when ordering spare parts. fig. 1 fig. 2...
  • Page 12: Instrument Panel (dashboard)

    Instrument panel (Dashboard) GEAR Instrument panel 1) LCD Dot-Matrix, (see page14). 2) REVOLUTION COUNTER (rpm). Indicates engine revs per minute. fig. 3 3) Neutral light N (GREEN) Illuminates when the gearbox is in neutral. 6) FUEL WARNING LIGHT (AMBER). 4) HIGH BEAM HEADLIGHT LIGHT (BLUE).
  • Page 13 9) Limiter light “Over rev”/ traction control light “DTC” 10) ABS LIGHTS (AMBER YELLOW) (fig. 3). (RED) (fig. 3): This turns on to indicate that ABS is disabled or not functioning. Over rev light Engine off / speed below 5 Km/h No limiter Light off Light flashing...
  • Page 14 11) CONTROL BUTTON (fig. 4) Button used to display and set instrument panel parameters with the position “▲“. 12) CONTROL SWITCH (fig. 4) Button used to display and set instrument panel parameters with the position “▼“. 13) HIGH-BEAM FLASHER BUTTON FLASH (fig. 4) The high-beam flasher button may also be used to for LAP functions.
  • Page 15: Lcd Unit Functions

    LCD unit functions Warning Any adjustments to the instrument panel must only be carried out when the motorcycle is stationary. Never operate the instrument panel controls while riding the motorcycle. 1) SPEEDOMETER. Gives road speed. 2) ODOMETER. GEAR Shows total distance travelled. 3) TRIP METER.
  • Page 16: Lcd - Parameter Setting/display

    LCD - Parameter setting/display At the end of the check, the instrument panel always displays the Odometer (TOT) as the “main“ indicator on the main display and the “riding style” on the round display. Note The check can be interrupted by pressing the button (1, fig.
  • Page 17: Vehicle Speed Indicator

    LCD Dot-Matrix (B, fig. 6): - WARNING (only if active) - ERRORS (only if active) - DESMO SERVICE (only if active) - SET UP - “Riding Style” indication set At this point, by pressing the (2, fig. 7) “▼” button it is possible to switch to the following functions: - RANGE - Remaining range - CONS I.
  • Page 18: Engine Rpm Indicator (rpm)

    Engine rpm indicator (RPM) This function displays the rpms. The instrument panel receives the engine rpm information and displays it. This information is displayed progressively from the left to the right, identifying the rpms. fig. 9...
  • Page 19: Engaged Gear Indicator

    Engaged gear indicator This function displays the gears. The instrument panel receives information and indicates the engaged gear or “N” for neutral. Note GEAR GEAR GEAR GEAR GEAR GEAR GEAR GEAR In the case of a gear sensor “error”, a dash “-” (not flashing) will be displayed.
  • Page 20: Clock

    Clock This function shows the time. Time is always displayed as follows: AM from 0:00 to 11:59 PM from 12:00 to 11:59 If battery power is suddenly cut off (Batt-OFF), when battery power is restored and at the next Key-On, the clock is reset and restarts from “0:00“.
  • Page 21: Fuel Level Indicator

    Fuel level indicator This function displays the fuel level. The low fuel light turns on when the level goes down to 2 marks and there are still 4 litres in the tank; if the level goes down further, the last mark will be displayed flashing. Important If the vehicle enters the reserve status and the light has turned on, it is recommended to turn the vehicle off...
  • Page 22: Coolant Temperature

    Coolant temperature vs. EU, CND, FRA, JAP This function indicates coolant indication state. Steady reading The temperature unit of measure can be selected (°C or °F). The reading is indicated as follows: Steady reading Steady reading - if the reading is between - 39°C and +39°C “LO” is shown flashing on the instrument panel (steady);...
  • Page 23: Total Distance Covered Indicator: "odometer

    Total distance covered indicator: vs.UK, USA vs. EU, CND, FRA, JAP “Odometer“ This function shows the total distance covered by the vehicle. At Key-On the system automatically enters this function. The odometer reading is stored permanently and cannot be reset. If the distance travelled exceeds 99999 km (or 99999 miles), the value “99999”...
  • Page 24: Trip 1" Meter

    “Trip 1“ meter vs.UK, USA vs. EU, CND, FRA, JAP This function shows the distance travelled since the trip meter was last reset. Holding the button (1, fig. 7) “▲“ pressed for 3 seconds when this function is displayed resets the trip meter. When the reading exceeds 999.9, distance travelled is reset and the meter automatically starts counting from 0 again.
  • Page 25: Indication If The Dtc Function Is Active/not Active

    Indication if the DTC function is active/not DTC ON DTC OFF active This function indicates if DTC (Ducati Traction Control) is active. When “DTC” is not lit up in the inside the rim, this means that the function is disabled.
  • Page 26: Warning Indication (alarms/signals)

    Warning indication (Alarms/Signals) The instrument panel shows some signals/malfunctions in real time on the circular “Dot-Matrix” display (B, fig. 19) that are not dangerous for correct vehicle operation. At Key-On (at the end of the check) one or more “warnings” are displayed if they are active.
  • Page 27: Low" Battery Level

    20 Traction Control (DTC) deactivated The activation of this “warning” indicates that DTC (Ducati Traction Control) has been turned off. Note In this case, Ducati recommends being very careful...
  • Page 28: Hands Free Key (hf) Not Recognised

    Free system does not detect the active key (1, fig. 59) near the vehicle. Note In this case, Ducati recommends checking that the active key (1, fig. 59) is near the vehicle (and has not been lost) and that it functions properly.
  • Page 29: High" Engine Coolant Temperature

    In this case, Ducati recommends turning the vehicle off and on (Key-Off / Key-On) holding the handlebar pressed down to the end stop. If the signal remains (and the steering does not “release”) contact a Ducati Dealer or Authorised Service Centre. fig. 25...
  • Page 30: Instrument Panel Diagnosis

    When one or more errors are displayed, always contact are displayed (only if they are active). a Ducati Dealer or Authorised Service Centre. If an “error” is activated during operation, the current indication on the circular “Dot-Matrix” display (B, fig. 6) will switch automatically to the indicator.
  • Page 31 WARNING LIGHT ERROR MESSAGE ERROR DEVICE ECU ECU control unit not functioning DEVICE DASHBOARD Instrument panel not functioning DEVICE HANDS FREE Hands Free control unit not functioning DEVICE BBS - DTC Black Box control unit not functioning THROTTLE POSITION Incorrect throttle position ACCELER.
  • Page 32 WARNING LIGHT ERROR MESSAGE ERROR COIL Coil INJECTOR Injector PICK-UP Timing/rpm sensor LAMBDA Lambda sensor LAMBDA HEATER Lambda heater FAN RELAY Fan relay HIGH BEAM High beam headlight relay LOW BEAM Low beam headlight relay CLAXON Horn CAN communication line BATTERY Battery voltage (HIGH or LOW) DEVICE DES...
  • Page 33 WARNING LIGHT ERROR MESSAGE ERROR DES GENERIC Problem related to suspension ECU operation STOP LIGHT Rear stop light ECU GENERIC ECU error KEY ERROR HF communication problem HANDS FREE GENERIC Hands Free ECU error DES FRONT COMPRESS. Problem with the stepper that adjusts suspension front compression DES FRONT REBOUND Problem with the stepper that adjusts front suspension...
  • Page 34: Maintenance Indicator

    (at the end of the initial check) Centre should be contacted to have the general maintenance the indication that you should go to a Ducati Dealer or or oil change performed. Authorised Service Centre to have the scheduled maintenance “DESMO SERVICE”...
  • Page 35: Maintenance Table

    Maintenance table Indicator Mileage travelled count down -1000 count down -1000 DESMO OIL SERVICE DESMO SERVICE OIL SERVICE SERVICE • 1000 • 11000 • 12000 • 23000 • 24000 • 35000 • 36000 • 47000 • 48000 • 59000 • 60000 •...
  • Page 36 fig. 26...
  • Page 37: Set Up - "riding Style Set" Indication

    SET UP - “Riding Style set“ indication “Base” version This function indicates the “Riding Style” set for the vehicle. Four “Riding Styles” are available: SPORT, TOURING, URBAN and ENDURO. Each riding style can be changed using the “Riding Style” function. In the “base”...
  • Page 38 “S” version fig. 29...
  • Page 39: Range" Indicator - Remaining Range

    (Key-On/engine off), the reading will be updated as soon as the vehicle starts to move (speed greater than zero). Warning The residual range that is measured is an approximate value; Ducati recommends not trying to use all the residual range indicated.
  • Page 40: Indicator "cons I." - Instantaneous Fuel Consumption

    Indicator “CONS I.“ - Instantaneous fuel vs. UK, USA vs. EU, CND, FRA, JAP consumption This function indicates the “instantaneous” fuel consumption. The calculation is made considering the quantity of fuel used and the distance travelled during the last second. The active calculation phase only occurs when the engine is running and the vehicle is moving (moments when the vehicle is not moving when speed is equal to 0 and/or when...
  • Page 41: Indicator "avg" - Average Speed

    Indicator “AVG” - Average speed vs. UK, USA vs. EU, CND, FRA, JAP This function shows the average speed of the motorcycle. The calculation is made considering the distance and time travelled since the last Trip 1 reset. When Trip 1 is reset, the value is set to zero and the first available value is shown on the display 10 seconds after the reset.
  • Page 42: Indicator "time Trip" - Trip Time

    When the detected temperature drops to 4°C (39°F), the display warns that the formation of ice is possible. The indication turns off when the temperature rises to 6°C (43°F). Warning This warning does not exclude the possibility of icy road sections even at temperatures above 4°C (39°F); when external temperatures are “low“...
  • Page 43: Riding Style" Function (riding Style Change)

    Each riding style is associated with a different intervention riding style at a low speed). level of the traction control (DTC - Ducati Traction Control) and different engine power and output. For the “S” version with electronic suspension, each riding style change is also associated with different motorcycle setup.
  • Page 44 “Base” and “S” version Press RESET Press RESET for 2 s. Press RESET Press RESET for 2 s. Press Press RESET RESET Press RESET for 2 s. Press RESET Press RESET for 2 s. fig. 37...
  • Page 45: Load" Function (setup Change)

    “LOAD” FUNCTION (setup change) Warning The setup change can lead to a different motorcycle This function, which is only available in the “S” version, riding style; it is recommended to be careful if changing the changes the vehicle setup. setup while riding (it is recommended to change the setup at Each individual riding style is associated with four different a low speed).
  • Page 46 Version “S” only press RESET for 2 sec. Press RESET for 2 sec. single passenger setup activation Press RESET Press RESET for 2 sec. single passenger with luggage setup activation Press Press RESET RESET Press RESET for 2 sec. two passenger setup activation Press RESET Press RESET for...
  • Page 47: Setting" Menu

    “Setting” menu The setting menu contains the following “items”: This menu is used to set/enable some motorcycle functions. - EXIT To access the “setting menu” press the button (2, fig. 7) - ABS “▼” for 2 seconds. - BATTERY - SETUP Note - B.LIGHT Once this menu has been accessed, it is not possible...
  • Page 48 Press “▼” for 2 sec. Press “▲” Press “▼” Press “▼” Press “▲” Press “▼” Press “▲” Press “▼” Press “▼” Press “▲” Press “▲” Press “▼” Press “▼” Press “▲” Press “▲” Press “▲” Press “▼” Press “▼” Press “▲” fig.
  • Page 49: Abs Disabling Function

    Note If the disabling request was not successful, the instrument panel will display “NOT DISABLED“ in the circular display (B, fig. 6). In this case, repeat the procedure. If the problem persists, contact your Ducati dealer or Authorised Service Centre.
  • Page 50 Press RESET Press RESET Press RESET 3 sec. Press “▲” Press “▼” Press RESET fig. 41...
  • Page 51: Battery Voltage Indicator (battery)

    Battery voltage indicator (BATTERY) This function describes the battery voltage indicator. To display the function, enter the “Setting” menu page 46 and access the “BATTERY” page. The information will be displayed as follows: - if battery voltage is between 11.8 and 14.9 Volt the reading will be displayed steady;...
  • Page 52 Press RESET Press RESET Press RESET Press RESET fig. 42...
  • Page 53: Riding Style" Customisation

    To change the electronic suspension parameters (only for “S” versions) see the “DES (Ducati Electronic Suspension)” paragraph. The parameters set by Ducati for each individual driving style can be reset with the ”DEFAULT” function. To reset the “default” parameters see the “DEFAULT...
  • Page 54 “S” “base” Press “▼” Press RESET Press “▼” Press RESET Press “▲” Press “▼” Press RESET Press “▼” Press “▲” Press RESET Press “▼” Press “▲” Press RESET fig. 43...
  • Page 55: Dtc (ducati Traction Control) Setting Function

    DTC (Ducati Traction Control) setting settings in the “Riding Styles“ that can be selected by the rider: function This function customises the intervention level of the DTC RIDING TYPE DEFAULT? LEVEL (Ducati Traction Control). To display the function, enter the “Setting” menu page 46...
  • Page 56 “Base” version “S” version Press RESET for Press RESET 3 sec. Press “▲” Press “▼” Press RESET Press “▼” for Press RESET Press “▲” for 4 sec. 4 sec. Press RESET fig. 44...
  • Page 57: Tips On How To Select The Sensitivity Level

    Tips on how to select the sensitivity level The choice of the correct level depends on 3 main variables: 1) The grip (type of tyre, amount of tyre wear, the road/ track surface, weather conditions, etc.) Warning 2) The characteristics of the path/circuit (bends all taken at The 8 level settings of the DTC were calibrated using similar speeds or at very different speeds) tyres of the same make, model and size as those originally...
  • Page 58 Tips for use on the track We recommend level 8 be used for a couple of full laps (to allow the tyres to warm up) in order to get used to the system. Then try levels 7, 6, etc., in succession until you identify the DTC intervention level that suits you best (always try each level for at least two laps to allow the tyres to warm up).
  • Page 59: Engine Setting Function (engine Power Control)

    ENGINE setting function (Engine Power Control) This function customises engine power and output. To display the function, enter the “Setting” menu page 46 and access the “SET UP” page. Use buttons (1, fig. 7) “▲” and (2, fig. 7) “▼” to select the riding style to be changed and press the reset button (14, fig.
  • Page 60 Press RESET for Press RESET 3 sec. Press “▲” Press “▼” Press RESET Press “▲” Press “▼” Press RESET Press RESET fig. 45...
  • Page 61: Des Setting Function (ducati Electronic Suspension)

    DES setting function (Ducati Electronic Suspension) Available in the “S” version only. To display the function, enter the “Setting” menu page 46 and access the “SET UP” page. Use buttons (1, fig. 7) “▲” and (2, fig. 7) “▼” to select the riding style to be changed and Press RESET press the reset button (14, fig.
  • Page 62 The three parameters to change appear on the circular display (B, fig. 6): - FRONT: adjustment of the front shock absorber rebound and compression; - REAR: adjustment of the rear shock absorber rebound and compression; - PRE-LOAD: adjustment of the rear shock absorber spring Press RESET preload.
  • Page 63 “FRONT” adjustment - the top of the circular display (B, fig. 6) will show the set compression [C.] and rebound [R.]; - use buttons (1, fig. 7) “▲” and (2, fig. 7) “▼” to select the parameter to change and press the reset button (14, fig.
  • Page 64 “S” version Press RESET RESET Press “▲” for 12 s Press “▲” RESET RESET Press RESET for 3 s Press “▼” for 12 s Press “▼” Press “▼” “▲” Press “▲” for 6 s Press “▲” RESET for 3 s RESET RESET Press...
  • Page 65 “REAR” adjustment - the top of the circular display (B, fig. 6) will show the set compression [C.] and rebound [R.]; - use buttons (1, fig. 7) “▲” and (2, fig. 7) “▼” to select the parameter to change and press the reset button (14, fig.
  • Page 66 “S” version Press RESET RESET Press “▲” for 12 s Press “▲” RESET RESET Press “▼” RESET for 3 s Press Press “▼” for 12 s Press “▼” “▲” Press “▲” for 6 s RESET for 3 s Press “▲” RESET RESET Press...
  • Page 67 “PRE-LOAD” adjustment - the top of the circular display (B, fig. 6) will show the “preload” and a bargraph indicating the set value; - use buttons (1, fig. 7) “▲” and (2, fig. 7) “▼” to select “NEW SET” and press the reset button (14, fig. 4); - the number to be changed is shown on the display;...
  • Page 68 Press RESET RESET Press “▼” Press “▲” for 4 s RESET for 3 s RESET RESET Press Press Press “▲” Press “▼” for 4 s “▼” “▲” Press Press “▼” “▲” Press RESET fig. 50...
  • Page 69: Default Function (resetting Ducati Default Parameters)

    DEFAULT function (Resetting Ducati default parameters) This function resets the parameters set by Ducati for each riding style. To display the function, enter the “setting” menu page 46 and access the “SET UP” page. Use the buttons (1, fig. 7) “▲”...
  • Page 70 Base version “S” version Press RESET Press “▼” Press “▲” Press RESET Press RESET fig. 51...
  • Page 71: Instrument Panel Backlighting Adjustment Function

    Instrument panel backlighting adjustment Note function In the event of an interruption of the power supply from the battery, when power is restored at the next Key-On, This function adjusts the instrument panel backlighting the backlighting will always be set by default to maximum intensity.
  • Page 72 Press RESET Press RESET Press Press “▲” Press Press “▼” “▼” “▼” Press RESET Press “▲” Press “▼” Press Press “▼” Press RESET RESET Press Press “▲” “▼” fig. 52...
  • Page 73: Lap Activation/deactivation Function (lap Time)

    LAP Activation/Deactivation function (lap time) This function activates and deactivates the LAP function (lap time). To display the function, enter the “setting” menu page 46 and access the “LAP” page. In the next display, press the reset button (14. fig. 4) showing “ON / OFF”.
  • Page 74 Press RESET Press RESET Press Press “▲” “▼” Press “▲” Press RESET Press RESET Press “▼” Press Press “▲” “▼” fig. 53...
  • Page 75: Lap Registration Function

    LAP registration function If however the LAP function is switched on and the memory has not been cleared, but fewer than 30 laps have been This function describes the “LAP“ time registration. saved (e.g. 18 laps), the instrument panel will store any If the function is activated (see “LAP activation/deactivation remaining laps until the memory is full (in this case, it will description”), the lap time can be registered as follows:...
  • Page 76 Press FLASH Press FLASH time time Press FLASH time Press FLASH time fig. 54...
  • Page 77: Stored Lap Display Function

    Stored LAP display function If while registering the LAP the engine reaches the threshold that precedes the rev limiter or rev limiter threshold, the This function displays the stored LAPs. relative light “Over Rev” (9, fig. 3) will turn on when To display the function, enter the “setting”...
  • Page 78 Press RESET Press RESET Press RESET Press “▲” Press “▼” Press Press RESET for RESET 3 sec. Press “▼” Press “▲” Press RESET fig. 55...
  • Page 79: Dtc (ducati Traction Control) On/off Function

    This function activates and deactivates the DTC (Ducati Traction Control). To display the function, enter the “setting” menu page 46 and access the “DTC”...
  • Page 80 Press RESET Press RESET Press “▲” Press “▼” Press RESET Press Press RESET Press “▲” RESET Press Press “▲” Press “▼” “▼” fig. 56...
  • Page 81: Digital Rpm Indication Function

    Digital RPM indication function This function displays the number of RPMs for improved accuracy when setting idle rpm. To display the function, enter the “setting” menu page 46 and access the “RPM” page. The display shows the numerical value of the RPM with a precision of 50 rpm.
  • Page 82 Press RESET Press RESET Press RESET Press RESET fig. 57...
  • Page 83: Clock Setting Function

    Clock setting function pressing button (1, fig. 7) “▲” the indication of the new time will flash and “MEM” will appear on the circular display. This function sets the clock. To confirm (store) the new set time press the reset button To display the function, enter the “setting”...
  • Page 84 Press RESET Press Press RESET for 3 s RESET Press “▲” Press “▼” Press RESET Press RESET for Press “▲” Press “▼” Press RESET Press RESET fig. 58...
  • Page 85: The Immobilizer System

    The immobilizer system For additional antitheft protection, the motorcycle is equipped with an IMMOBILIZER, an electronic system that locks the engine automatically whenever the ignition switch is turned off. The grip of each ignition key contains an electronic device that modulates the output signal from a special antenna in the top fairing when the ignition is switched On.
  • Page 86 The key contains a battery that must be replaced when the message “low level“ is displayed under the key and battery symbols when the instrument panel is turned on (fig. 61). Note In this case, replace the battery as soon as possible (page 86).
  • Page 87: Replacing The Battery In The Active Key

    Replacing the battery in the active key Only use 3 Volt CR 2032 lithium ion batteries. Note The keys do not need to be reprogrammed after replacing the battery. Remove the metal part of the battery. Use a large sized coin to pry open the shells of the plastic grip (2€...
  • Page 88 Remove the battery (2, fig. 64) from the printed circuit board (1, fig. 64) and replace it with a new one. Pay attention to polarity: the positive pole (+) must face upward. Important Only use the required type of battery. Reinsert the printed circuit board (1, fig.
  • Page 89 Apply slight pressure on the antenna (3, fig. 66) of the printed circuit board until you hear a click. Align the two shells of the grip and press on the area indicated by the arrows (fig. 67) to reclose them. Make sure that you hear a “click”...
  • Page 90: Duplicate Keys

    If you need any duplicate keys, contact the Ducati Service network with all the keys you have left. The Ducati Service Centre will program all the new keys as well as any keys you already have. You may be asked to provide proof that you are the legitimate owner of the motorcycle.
  • Page 91: Immobilizer Override Procedure

    “setting” code; if there is already a stored PIN, contact an Authorised menu. Ducati dealer to have the function “reset“. To perform this From this moment, “MODIFY” will be displayed when procedure, the Authorised Ducati Dealer may ask you to accessing the “PIN CODE”...
  • Page 92 RESET press press press press “▼” “▼” “▼” “▼” press press press press “▼” “▼” “▼” “▼” press press press press “▼” x 6 “▼” x 2 “▼” x 4 “▼” x 8 RESET PIN not stored RESET RESET RESET “▲”...
  • Page 93 PIN CODE change function If the code is not correct, “OLD PIN WRONG” will appear for 3 seconds and then the instrument panel will return This function changes your four number PIN CODE. displaying “MODIFY” so you can repeat the attempt of To display the function, enter the “setting”...
  • Page 94 RESET RESET press “▼” press “▼” press “▼” press “▼” press “▼” press “▼” press “▼” press “▼” press press press press “▼” x 2 “▼” x 4 “▼” x 6 “▼” x 8 RESET RESET RESET RESET NEW PIN “▲”...
  • Page 95 If the code was entered correctly the message “NEW PIN” and four dashes “- - - -” will appear on the circular display; now enter the “new“ 4 digit code. Entering the “new” PIN: each time you press the button (2, fig.
  • Page 96 - - - RESET press “▼” press “▼” press “▼” - - - press “▼” press “▼” press “▼” press “▼” - - - press press press press “▼” x 2 “▼” x 4 “▼” x 6 - - - “▼”...
  • Page 97: Light Control

    Light control Turn signals (automatic reset) The instrument panel controls the automatic reset of the turn signals. Headlight control After activating one of the two turn signals, they can be This function allows you to reduce current consumption from deactivated using the RESET button (14, fig. 4). the battery, by automatically managing headlight switching- If the turn signal is not “reset“...
  • Page 98 If there is a sudden interruption in the battery while the function is active, the instrument panel will disable the function when the voltage is restored. Warning The frequent use of this function can considerably reduce the battery charge; Ducati recommends using this function only when necessary.
  • Page 99 “Steering in position for being locked” indication This function informs that the steering is in position for turning on the steering lock. The sensors detect that the steering is in position during the first 60 seconds after turning off the vehicle and the instrument panel activates the indication on the circular display for max.
  • Page 100: Controls

    Controls Warning This section shows the position and function of the controls used to drive the motorcycle. Be sure to read this information carefully before you use the controls. Position of motorcycle controls (fig. 74) 1) Instrument panel. 2) “Hands free” system. 3) Left-hand handlebar switch.
  • Page 101: Hands Free" System

    “Hands free” system The Hands free system consists of: 1) Hands free lock; 2) Antenna; 3) Active key; 4) Passive key; 5) Electric cap (optional). The “Hands free” lock (1, fig. 75) is located on the front of the tank. The door must be removed to access it (2). Note In the USA version the door (2, fig.
  • Page 102 Hands free system Key-On and Key-Off Key-On consists in turning on the hands free system and all of its electronic devices. Key-Off consists in turning off the hands free system and all electronic devices, and makes sure the engine is turned off. Key-On is done using the button (6) on the handlebar on the right switch or using the emergency button (7) on the Hands free lock (1, fig.
  • Page 103 Note When the battery is discharged, the active key (3, fig. 75) acts like a passive key (4, fig. 75). The instrument panel displays the discharged battery status. The mechanical part (A) of the key (3) is used to open the fuel cap and the seat and bag lock.
  • Page 104 Key-On/Key-Off using the red key on the handlebar with the active key A Key-On can be performed by pressing the red key (6) on the handlebar in the HANDS FREE ON/OFF position and in the presence of the active key (3, fig. 75). Note The active key (3, fig.
  • Page 105 Key-On/Key-Off using the key on the Hands free lock with the active key Key-On can be performed by pressing the button (7) on the Hands free lock (1, fig. 75) and with the presence of the active key (3, fig. 75). Note In the USA version the door (8) is not present.
  • Page 106 Key-On/Key-Off using the red key on the handlebar with the passive key A Key-On can be performed by pressing the red button (6) on the handlebar in the HANDS FREE ON/OFF position and in the presence of the passive key (4, fig. 75). Note The passive key (4, fig.
  • Page 107 Key-On/Key-Off using the key on the Hands free lock with the passive key Key-On can be performed by pressing the button (7) on the Hands free lock and with the presence of the passive key (4, fig. 75). Note In the USA version the door (8) is not present. Note The passive key (4, fig.
  • Page 108 Key-On/Key-Off using the pin code (immobilizer release) Note In the USA version the door (8) is not present. Key-On can be performed by pressing the button (7) on the hands free lock (1, fig. 75) without the presence of the keys (3, fig.
  • Page 109 If the code is incorrect, the instrument panel will return to the If this procedure is necessary in order to start the initial indication in order to enter the code again. vehicle, contact an Authorised Ducati Service Centre as soon as possible to fix the problem.
  • Page 110 press “▼” press “▼” press “▼” press “▼” press “▼” press “▼” press “▼” press “▼” press“▼” press “▼” press “▼” press “▼” RESET RESET RESET RESET Correct PIN? The correct PIN will flash on the instrument panel for 4 seconds, after which the instrument panel comes back to the “main“...
  • Page 111: Lh Switch

    LH switch (fig. 74) 1) Dip switch, light dip switch, two positions (fig. 90): (A) pushed up = low beam on; (B) pushed down = high beam on; (C) pushed to the side = high beam flasher (FLASH), “Start-Stop lap” function. 2) Button = three-position turn signal (fig.
  • Page 112: Clutch Lever

    Clutch lever (fig. 92) Lever (1) disengages the clutch. It features a dial adjuster (2) for lever distance from the twistgrip on handlebar. The lever distance can be adjusted through 10 clicks of the dial (2). Turn clockwise to increase lever distance from the twistgrip.
  • Page 113: Rh Switch

    RH switch (fig. 93) 1) Red ON/OFF switch. 2) Black ENGINE START button The switch (1, fig. 93) has three positions: A) centre: RUN OFF. In this position, the engine cannot be started and all electronic devices are off. B) pushed down: ON/OFF. In this position, the system can be turned on (Key-On) and off (Key-Off).
  • Page 114: Throttle Twistgrip

    Throttle twistgrip (fig. 95) The twistgrip on the right handlebar opens the throttles. When released, it will spring back to the initial position (idling speed). Front brake lever fig. 95 (fig. 96) Pull in the lever (1) towards the twistgrip to operate the front brake.
  • Page 115: Rear Brake Pedal

    Rear brake pedal (fig. 97) Push down on the pedal with your foot to operate the rear brake. The system is hydraulically controlled. fig. 97 Gear change pedal (fig. 98) The gear change pedal is at rest when in centre position N with automatic spring-back.
  • Page 116: Adjusting The Position Of The Gearchange And Rear Brake Pedals

    Adjusting the position of the gearchange and rear brake pedals The position of the gearchange and rear brake pedals in relation to the footrests can be adjusted to suit the requirements of the rider. Adjust the pedals as follows: Gear change pedal (fig.
  • Page 117 Rear brake pedal (fig. 100) loosen counter nut (7). Turn pedal travel adjusting screw (6) until pedal is in the desired position. 1,5÷2 mm Tighten the counter nut (7). Operate the pedal by hand to check that there is 1.5 to 2 mm of freeplay before the brake bites.
  • Page 118: Main Components And Devices

    Main components and devices Position on the vehicle (fig. 101) 1) Tank filler plug. 2) Seat lock. 3) Side stand. 4) Power outlet 5) Rear-view mirrors. 6) Front fork adjusters. 7) Rear shock absorber adjusters. 8) Catalytic converter. 9) Exhaust silencer (see ”Warning” on page 137). fig.
  • Page 119: Tank Filler Plug

    Tank filler plug Opening Lift the cover (1, fig. 102) and insert the active or passive key into the lock. Give the key a 1/4 turn clockwise to unlock. Lift the plug (2, fig. 103). Closing Close the cap (2) with the key inserted and press it into its seat.
  • Page 120: Seat Lock

    Seat lock CLOSE By operating the lock (1, fig. 104) the passenger seat can be removed to access the tool kit compartment and the rider seat to access the battery and other devices. Removal of the seats OPEN Insert the active or passive key into the lock (1) and rotate it clockwise until you hear the release click in the passenger seat.
  • Page 121 To remove the rider seat (4, fig. 106) remove the rear part from the pins (5) on the frame. Pull it backwards and at the same time push the front part of the rider seat downwards to unhook it from the pins (6, fig. 107) on the tank.
  • Page 122 Refitting Position the front part of the rider seat (4), with slots (7, fig. 108), in the pins (6, fig. 107) of the tank. Push on the front end of the rider seat to move the pins (6) to the bottom of the slots (7). Insert the rear part of the rider seat into the pins (5, fig.
  • Page 123: Side Stand

    Side stand (fig. 109) Important Before lowering the side stand, check that the ground is sufficiently even and firm. Do not park on soft or pebbled ground or on asphalt melted by the sun heat and similar or the motorcycle may fall over. When parking on a slope, always park with the rear wheel on the downhill side.
  • Page 124: Power Outlet

    Power outlet The motorcycle has two power outlets to power the accessories. The outlets are protected by a 10 A fuse located in the rear fuse box. The power outlets are positioned on the left (1, fig. 110) and right (2, fig. 111) sides of the motorcycle behind the passenger pedal support bracket.
  • Page 125: Adjusting The Front Fork

    Adjusting the front fork The front fork used on this motorcycle has rebound, compression and spring preload adjustment. The settings are adjusted using external adjuster screws. 1) to adjust rebound damping (fig. 112); 2) to adjust spring preload (fig. 112); 3) to adjust compression damping (fig.
  • Page 126: Des Setting Function (ducati Electronic Suspension)

    In the ”S” model, the fork is adjusted by electric impulses sent by the instrument panel to the adjusters (fig. 114) inside the fork legs. For fork adjustment, follow the description on page 60 ”DES setting function (Ducati Electronic suspension)”. fig. 114...
  • Page 127: Adjusting The Rear Shock Absorber

    Adjusting the rear shock absorber The rear shock absorber has external commands that enable you to adjust the setting to suit the load on the motorcycle. The adjuster (1, fig. 115) located on the lower connection holding the shock absorber to the swingarm adjusts the damping during the rebound phase (return).
  • Page 128 To access the adjuster (3, fig. 116) remove the rider seat and the cover (4, fig. 117) located to the side of the battery. The adjuster (3, fig. 116) can be turned through the hole in the battery support. Turning the adjusters (1) and (3) or the knob (2) in a clockwise direction increases the damping or the preload;...
  • Page 129: Motorcycle Setup Variation ("s" Version Only)

    Motorcycle setup variation (”S” version Single passenger only) Motorcycle setup is the optimal result of tests carried out under different riding conditions by our technical staff. The rider can set four different setup configurations on the Single passenger with luggage instrument panel: - Single passenger;...
  • Page 130: Directions For Use

    Directions for use For the first 100 km use the brakes gently. Avoid sudden or prolonged braking. This will allow the friction material on the brake pads to bed in against the brake discs. To allow all the mechanical moving parts in the motorcycle to adapt to one another, and to avoid shortening the life of the main engine components, it is advisable to avoid sudden acceleration and running the engine at high rpm for too long,...
  • Page 131 Throughout the running-in period, be careful to stick to the recommended maintenance schedule and periodic service intervals indicated in the warranty booklet. Failure to follow these instructions releases Ducati Motor Holding S.p.A. from any liability whatsoever for any engine damage or shorter engine life.
  • Page 132: Pre-ride Checks

    BRAKE AND CLUTCH FLUID In case of malfunction, do not ride the motorcycle and Check fluid level in the relevant reservoirs (page 145). contact a Ducati Dealer or authorised Service Centre. COOLANT LEVEL Check coolant level in the expansion reservoir. Top up if needed (page 144).
  • Page 133: Abs Device

    ABS device Check that the front (1, fig. 121) and rear (2, fig. 122) phonic wheels are clean. Warning Clogged reading slots would compromise system proper operation. It is recommended to disable ABS system in case of muddy road surface because under this condition the system might be subject to sudden failure.
  • Page 134: Engine On/off

    Engine on/off Warning Before starting the engine, become familiar with the controls you will need to use when riding (page 99). Warning Never start or run the engine indoors. Exhaust gases are toxic and may lead to loss of consciousness or even death within a short time.
  • Page 135 Note It is possible to start the engine with side stand down and the gearbox in neutral. When starting the bike with a gear engaged, pull the clutch lever (in this case the side stand must be up). Move the red switch (1) up to uncover the black button (4, fig.
  • Page 136: Moving Off

    Moving off Braking 1) Disengage the clutch by squeezing the clutch lever. Slow down in time, shift down to engine-brake first and then 2) Push down the gear change lever firmly with the tip of brake applying both brakes. Pull the clutch lever before your foot to engage first gear.
  • Page 137: Abs System

    ABS system If desired, the system can be deactivated from the instrument panel, using the ”ABS disabling function”. Using the brakes correctly under adverse conditions is the hardest – and yet the most critical - skill to master for a rider. Warning Braking is one of the most difficult and dangerous moments Use both the brake lever and the brake pedal for...
  • Page 138: Stopping The Motorcycle

    Stopping the motorcycle Reduce speed, shift down and release the throttle twistgrip. Shift down to engage first gear and then neutral. Apply the brakes and bring the motorcycle to a complete stop. Turn off the engine moving the red switch downward (1, fig. 127). Parking Park the stopped motorcycle on the side stand.
  • Page 139 (Key-Off / Key-On) holding the handlebar pressed down to the end stop. If the signal remains (and the steering does not ”release”) contact an Authorised Ducati Service Centre. In order to make the motorcycle visible at night or in poorly illuminated areas, the ”Parking”...
  • Page 140 Press (2, fig. 130) for at least 3 seconds: the indication of the activated function (fig. 131) will appear on the circular display of the instrument panel for 5 seconds and the lights will remain on for 2 hours. After this period of time, they will turn off automatically.
  • Page 141: Refuelling

    Refuelling ( fig. 132 Never overfill the tank when refuelling. The fuel level should always be below the rim of the filler recess. Warning Use low-lead fuel with 95 octane rating at origin minimum (see ”Top-ups” table, page 170). Check that no fuel is trapped in the filler cap recess. Max level fig.
  • Page 142: Tool Kit And Accessories

    - long rear mudguard kit. Front semi-mudguard kit (fig. 134) Important To fit the from semi-mudguard kit, ALWAYS contact a Ducati Dealer or Authorised Service Centre. Remove the pipe grommet (1, fig. 134) unscrewing the two screws (2, fig. 134). fig. 134...
  • Page 143 Position the front semi-mudguard kit (3) on the front mudguard, housing the front brake pipe (4) and the front phonic wheel cable (5) as shown in the figure (fig. 136). Fasten the slot (A) in the fissure in the front mudguard (1) and start the two previously removed screws (2).
  • Page 144: Long Rear Mudguard Kit

    Long rear mudguard kit Important To fit the long rear mudguard kit, ALWAYS contact a Ducati Dealer or Authorised Service Centre. Remove the rear mudguard (1) unscrewing the three screws (2). Position the long rear mudguard kit (3) on the swingarm, starting the previously removed screws (2).
  • Page 145: Main Maintenance Operations

    Main maintenance operations Warning This operation must be carried out with the engine cold and with the motorcycle vertical and level. Checking and topping up coolant level Check the coolant level in the expansion reservoir on the right-hand side of the headstock. Steer the handlebar completely to the left and check that the level is between the MIN and MAX marks on the side of the expansion reservoir.
  • Page 146: Checking Brake And Clutch Fluid Level

    Brake system If you find exceeding play on brake lever or pedal and brake pads are still in good condition, contact your Ducati Dealer or authorised Service Centre to have the system inspected and any air drained out of the circuit.
  • Page 147: Clutch System

    If the control lever has exceeding play and the transmission snatches or jams as you try to engage a gear, it means that there might be air in the circuit. Contact your Ducati Dealer or authorised Service Centre to have the system inspected and air drained out.
  • Page 148: Checking Brake Pads For Wear

    The pads must be replaced when approx. 1 mm of friction material (fig. 142 and fig. 143) can be seen through the opening between the callipers. Important Have the brake pads replaced at a Ducati Dealer or authorised Service Centre. fig. 142 1 mm...
  • Page 149: Lubricating Cables And Joints

    Ducati Dealer or Authorised Service Centre. To avoid this kind of problem with the throttle cable, unscrew the two retaining screws (1, fig.
  • Page 150: Adjusting Throttle Control Free Play

    Adjusting throttle control free play 1,5÷2 mm ➤ The throttle twistgrip must have free play of 1.5 - 2.0 mm in all steering positions, measured on the outer edge of the twistgrip. If necessary, adjust it using the adjusters (1 and 2, fig.
  • Page 151: Charging The Battery

    Charging the battery Warning (fig. 148) Keep the battery out of the reach of children. Before charging the battery, it is recommended to remove it from the motorcycle. Charge the battery at 0.9 A for 5÷10 hours. Remove the rider seat, unscrew the screw (1) and remove the bracket (2).
  • Page 152: Checking Drive Chain Tension

    Checking drive chain tension (fig. 149) Important Have chain tension adjusted by a Ducati Dealer or authorised Service Centre. Measure chain tension at the centre of the lower section, with the motorcycle on the side stand: lower the chain by...
  • Page 153: Chain Lubrication

    To access the screws (1), remove the rear gravel guards (2, fig. 150) and chain guard (3), unscrewing the three screws (4). fig. 151 Chain lubrication The chain fitted on your motorcycle has O-rings that keep dirt out of and lubricant inside the sliding parts. So as not to damage these seals when cleaning the chain, use special solvents and avoid aggressive washing with high- pressure steam cleaners.
  • Page 154: Replacing The High And Low Beam Bulbs

    Replacing the high and low beam bulbs Before replacing a burnt-out bulb, make sure that the new bulb complies with the voltage and wattage specified in the “Wiring diagram”, page 176. Always test the new bulb before refitting any parts you have removed. fig.
  • Page 155 Unscrew the four screws (3, fig. 154) that fasten the panel (4) to top fairing. Remove the panel (4), lifting the rear part to unhook the tabs from the slots (A, fig. 155) in the top fairing. Detach the connector (5) from the bulb holder (6). Turn the bulb holder with the burnt-out bulb anticlockwise and remove it.
  • Page 156: Rear Turn Signals

    (A, fig. 155) made in the top fairing. Note To replace the parking light LED bulb, contact an Authorised Ducati Service Centre. Rear turn signals (fig. 157) Remove the screw (1) and detach the glass (2) from the fig.
  • Page 157: Number Plate Light

    Number plate light (fig. 158) To access the bulb in the number plate light open the number plate lens (3), pull the bulb (4) out of the holder and replace it. Beam setting (fig. 159) When checking beam setting, put the motorcycle upright. Tyres should be inflated at the correct pressure and one person should be sitting astride the motorcycle, keeping it at right angles to its longitudinal axis.
  • Page 158 The height of the headlight beam can be adjusted using the adjusting screws (1, fig. 160) located at the bottom on the sides of the headlight. Turning the screw (1) of the headlight clockwise, the light beam will move downwards: turning it in the opposite direction, will move it upwards.
  • Page 159: Rear-view Mirror Adjustment

    Rear-view mirror adjustment (fig. 161) The rear-view mirror can be adjusted manually by pressing points (A). fig. 161...
  • Page 160: Tubeless Tyres

    2.50 bar (rider only) - 2.9 bar (with passenger and/or bags) As tyre pressures are affected by changes in temperature Have the tyres replaced at a Ducati Dealer or and altitude; check and adjust them whenever you are riding authorised Service Centre. Correct removal and installation in areas where there are large variations in temperature or of the wheels is essential.
  • Page 161 Minimum tread depth Measure tread depth (S, fig. 162) at the point where tread is most worn down. It should not be less than 2 mm, and in any case not less than the legal limit. Important Visually inspect the tyres at regular intervals for cracks and cuts, especially on the side walls, and bulges or large stains that indicate internal damage.
  • Page 162: Checking Engine Oil Level

    (2) and top up to correct level. Replace the filler cap. Important Engine oil and oil filters must be changed by a Ducati Dealer or authorised Service Centre at the intervals specified in the scheduled maintenance table reported in the Warranty Booklet.
  • Page 163: Cleaning And Replacing The Spark Plugs

    The condition of the spark plugs provides a good indication of how well the engine is running. Have the spark plugs inspected or replaced at an Ducati Dealer or Authorised Service Centre; they will check the colour of the ceramic insulator of the central electrode (1): an even brown colour is a sign that the engine is in good running order.
  • Page 164: General Cleaning

    General cleaning Warning There may be loss of braking efficiency immediately To preserve the finish of metal parts and paintwork, wash after washing the motorcycle. Never grease or lubricate the and clean your motorcycle at regular intervals, anyway brake discs. This will cause loss of braking efficiency. Clean according to the road conditions you ride in.
  • Page 165: Storing The Bike Away

    If the motorcycle has been left unused for more than a month, the battery should be checked and recharged if necessary. Protect the motorcycle with a specific motorcycle cover that will not damage the paintwork or retain moisture. This type of motorcycle cover is available from Ducati Performance.
  • Page 166: Scheduled Maintenance Chart

    Scheduled maintenance chart Operations to be carried out by the dealer List of operations to be performed at 1000 km Reading of the error memory with DDS on the engine control units, vehicle and ABS Change the engine oil Change the engine oil filter Check the indicators and lighting Check the safety devices (side stand switch, clutch lever switch, right switch engine stop switch and gear position sensor) Check the battery charge level...
  • Page 167 List of operations to be performed at 1000 km Check the drive chain tension and lubrication Check the freedom of movement of the side and central stand (if installed) Check the tightening of the safety components (ex. wheel disc nuts, brake callipers, sprocket tightening) Check rubbing points, clearance and freedom of movement of the flexible cables and electric wiring in view Road test of the motorcycle, testing the safety devices (ex.
  • Page 168: Operations To Be Carried Out By The Dealer

    Operations to be carried out by the dealer List of operations to be performed every 12000 km / year (first limit reached) Reading of the error memory with DDS on the engine control units, vehicle and ABS Change the engine oil Change the engine oil filter Check and/or adjust valve clearance (only every 24000 km) Replace the timing belts (only every 24000 km/60 months)
  • Page 169: Operations To Be Carried Out By The Customer

    List of operations to be performed every 12000 km / year (first limit reached) Check the freedom of movement of the side and central stand (if installed) Check the tightening of the safety components (ex. wheel disc nuts, brake callipers, sprocket tightening) Check rubbing points, clearance and freedom of movement of the flexible cables and electric wiring in view Road test of the motorcycle, testing the safety devices (ex.
  • Page 170: Technical Data

    Technical data Carrying full load: 430 kg. Warning Overall dimensions (mm) (fig. 165) Failure to observe weight limits could result in poor handling and impair the performance of your motorcycle, and you may lose control of the vehicle. Weights Weight in running order without fluids and battery 192 kg.
  • Page 171 TOP-UPS TYPE Fuel tank, including a reserve of 4 cu. dm (litres) Unleaded fuel with 95 fuel octane rating (at 20,0 cu. dm (litres) least) Lubrication circuit SHELL - Advance Ultra 4 4.10 cu. dm (litres) Front/rear brake and clutch circuits Special hydraulic fluid SHELL Advance Brake —...
  • Page 172: Engine

    Engine Timing system Twin cylinder, four-stroke, 90° “L“ type, longitudinal. DESMODROMIC (type) with four valves per cylinder, Bore, mm: operated by eight rocker arms (4 opening rockers and 4 closing rockers) and two overhead camshafts. It is operated Stroke, mm: by the crankshaft through spur gears, belt rollers and toothed 67.9 belts.
  • Page 173: Performance Data

    56 mm Injectors per cylinder: 1 Holes per injector: 12 Important Fuel supply: 95-98 RON. Failure to follow these instructions will release Ducati Motor Holding S.p.A. from any liability for any engine damage or shortened engine life. Spark plugs Make:...
  • Page 174: Brakes

    Brakes Rear Separate-action anti-lock brake system operated by hall-type Fixed drilled steel disc. sensors mounted to each wheel, with phonic wheel Disc diameter: detection: ABS can be disabled. 245 mm. Hydraulically operated by pedal on right-hand side. Make: Front BREMBO Semi-floating drilled dual disc.
  • Page 175: Transmission

    Service Centre. Gearbox output sprocket/rear chain sprocket ratio: 15/40 Warning Total gear ratios: If the rear sprocket needs replacing, contact a Ducati gear 15/37 Dealer or authorised Service Centre. Incorrect replacement gear 17/30 of this component could seriously compromise your safety gear 20/27 and cause irreparable damage to the motorcycle.
  • Page 176: Frame

    Frame Suspensions ALS 420 steel tube trellis frame. ALS 450 steel tube trellis frame rear subframe. Front Die-cast light alloy connecting side plates, pivoted on the Hydraulic upside-down fork provided with external adjusters engine. for rebound and compression damping and preload (for inner Steering head angle: 24°...
  • Page 177: Exhaust System

    2xH11 (12V-55W); Parking light: led bulb (13.5V-4W). MTS1200 ABS Electrical controls on handlebars. Ducati Anniversary red 473.101 (PPG); Turn signals: Clear lacquer part no. 228.880 (PPG); Front: LED (9.8 V - 2.2 W); Racing Gray frame and black wheel rims.
  • Page 178 Fuses There are twelve fuses that protect the electric components located inside the front and rear fuse boxes, and one on the electric solenoid starter. There is a spare fuse in every box. Refer to the table below to identify the circuits protected by the various fuses and their ratings.
  • Page 179 The rear fuse box (B, fig. 168) is located on the right frame on the rear sub-frame, to the side of the ABS control unit. To access the fuse box, remove the rider seat (see page 119). To expose the fuses, take off the box protective cover. Mounting position and ampere capacity are marked on box cover.
  • Page 180 The main fuse (C, fig. 169), is positioned in front of the rear fuse box, on the solenoid starter (D). Remove the fuse cap (E) to reach it. A blown fuse is identified by the interrupted centre link (F, fig. 170). Important To prevent short circuits, replace the fuse after the Key-Off.
  • Page 181 Injection/electrical system diagram legend 1200 ABS 1) Right-hand handlebar switch 31) Antitheft alarm 59) Instrument panel 2) Immobilizer 32) Exhaust valve starter motor 60) Front right turn signal 3) Hands Free relay 33) Gear sensor 61) Low beam headlight relay 4) Hands free 34) Rear speed sensor 62) Left low beam headlight...
  • Page 182 Injection/electrical system diagram legend 1200 S ABS 1) Right-hand handlebar switch 31) Antitheft alarm 59) Instrument panel 2) Immobilizer 32) Exhaust valve starter motor 60) Front right turn signal 3) Hands Free relay 33) Gear sensor 61) Low beam headlight relay 4) Hands free 34) Rear speed sensor 62) Left low beam headlight...
  • Page 183 Wire colour coding B Blue W White V Violet BK Black Y Yellow R Red LB Light blue GR Grey G Green BN Brown O Orange P Pink Note The electrical system wiring diagram is at the end of this manual.
  • Page 184: Scheduled Maintenance Reminder

    Scheduled maintenance reminder DUCATI SERVICE MILEAGE DATE 1000 12000 24000 36000 48000 60000...
  • Page 185: For United States Of America Version Only

    Such use could lead to upset or other accident. Noise emission warranty Ducati Motor S.p.A. warrants that this exhaust system, at the time of sale, meets all applicable U.S. EPA Federal noise Reporting of safety defects standards.
  • Page 186: Tampering Warning

    If you are aware of any of the following symptoms, have the Tampering warning vehicle inspected and repaired by your local Ducati dealer. Tampering with Noise Control System Prohibited. Federal Symptoms: Law prohibits the following acts or causing thereof: Hard starting or stalling after starting.
  • Page 187: Riding Safety

    Riding safety The throttle should also be used judiciously to avoid skidding the rear wheel from too rapid acceleration or deceleration. The points given below are applicable for every day On rough roads, exercise caution, slow down, and grip the motorcycle use and shoud be carefully observed for safe and fuel tank with your knees for better stability.
  • Page 188: Protective Apparel

    This motorcycle was not intended to be equipped with a sidecar or to be used to tow any trailer or other vehicle. Ducati does not manufacture sidecars or trailers and cannot predict the effects of such accessories on handling or...
  • Page 189 Label location (fig. B) Right side Right side Only Canada fig. B...
  • Page 190 35 ÷ 37 mm 3 (Only Canada)
  • Page 191: Your Warranty Rights And Obligations

    - You are responsible for presenting your motorcycle to a injection system, the ignition system, catalytic converter, Ducati dealer as soon as a problem exists. The warranty and engine computer. Also included may be hoses, belts, repairs should be completed in a reasonable amount of connectors and other emission-related assemblies.
  • Page 192: California Evaporation Emission System

    United States of America in compliance with the Clean Air Act and applicable regulations of the United States Environmental Protection Agency and the California Air Resources Board. Any part or parts replaced under this warranty shall become the property of Ducati. fig. C...
  • Page 193 Ducati motorcycle for any purpose. Some states do not allow the exclusion or limitation...
  • Page 194 Ducati North America, Inc.. apply to you. 10443 Bandley Drive C. No dealer is authorized to modify this Ducati Limited Cupertino, California, 95014 Emission Control Systems Warranty. Tel: 001.408.253.0499 Fax: 001.408.253.4099 IV.
  • Page 195: Routine Maintenance Record

    Routine maintenance record DUCATI MILEAGE DATE SERVICE NAME 1,000 12,000 7,500 24,000 15,000 36,000 22,500 48,000 30,000 60,000 37,500...
  • Page 196 STARTER ENGINE STOP UNLOCK BW Bk FREE PUSH Dash Light 1-34 35-68 R/Bk B/Bk 1 2 3 4 1 2 3 Gr/G N.C. 3 4 5 B/Bk Gr/G Gr/Bk Gr/Bk R/Gr R/Bk P/Bk P/Bk R/Bk R/Bk Lb/Bk Lb/Gr R/Bk Bn/Y Bk/Y Bk/W Bk/O...
  • Page 197 STARTER ENGINE STOP UNLOCK BW Bk FREE 69 70 PUSH 1-34 35-68 R/Bk B/Bk 1 2 3 4 1 2 3 Gr/G 3 4 5 B/Bk Gr/Bk Gr/G Gr/Bk R/Bk R/Gr P/Bk 1 2 3 4 1 2 3 4 P/Bk 1 2 3 4 5 R/Bk...
  • Page 199 cod 913.7.170.1B...

This manual is also suitable for:

Multistrada 1200s abs

Comments to this Manuals

Symbols: 0
Latest comments:
  • Shaun Jan 07, 2017 06:19:
    Very useful, thank you. Dont have to take the paper version out in the garage and get it covered in oil, grease etc.