Xconfiguration Video Allowwebsnapshots; Xconfiguration Video Osd Inputmethod Cyrillic; Xconfiguration Video Osd Inputmethod Inputlanguage; Xconfiguration Video Osd Loginrequired - Cisco TelePresence System Codec C90 Reference Manual

Cisco TelePresence System Codec C90
Contents Introduction

xConfiguration Video OSD MyContactsExpanded

Set how the local contacts will be displayed in the phone book dialog in the OSD (On Screen Display).
Requires user role: ADMIN
Value space: <On/Off>
On: The local contacts in the phone book will be shown in the top level of the phonebook dialog.
Off: The local contacts will be placed in a separate folder called MyContacts in the phonebook
dialog.
Example: xConfiguration Video OSD MyContactsExpanded: Off

xConfiguration Video OSD Output

The Video OSD (On Screen Display) Output lets you define which monitor should display the on
screen menus, information and icons. By default the OSD is sent to the monitor connected to the
Video OSD Output 1. If you cannot see the OSD on screen, then you must re-configure the OSD
Output. You can do this by entering a key sequence on the remote control, from the web interface, or
by a command line interface.
Using the remote control: Press the Disconnect key followed by: * # * # 0 x # (where x is output 1 to
4).
Using the web interface: Open a web browser and enter the IP address of the codec. Open the
Advanced Configuration menu and navigate to Video OSD Output and select the video output.
Using a command line interface: Open a command line interface and connect to the codec (if in doubt
of how to do this, see the API Guide for the codec). Enter the command: xConfiguration Video OSD
Output [1..4] (select the OSD Output)
Requires user role: ADMIN
Value space: <1..4>
Range: Select 1 for HDMI 1 output, select 2 for DVI-I 2 output, select 3 for HDMI 3 output, or
select 4 for DVI-I 4 output.
xConfiguration Video OSD Output: 1
Example:

xConfiguration Video OSD InputMethod InputLanguage

The codec can be enabled for Cyrillic input characters in the menus on screen. NOTE: Requires that
xConfiguration Video OSD inputMethod Cyrillic is set to On.
Requires user role: ADMIN
<Latin/Cyrillic>
Value space:
Latin: Latin characters can be entered when using the remote control (default).
Cyrillic: Cyrillic characters can be entered using the remote control. NOTE: Requires a Cisco
TelePresence Remote Control with Cyrillic fonts.
xConfiguration Video OSD InputMethod InputLanguage: Latin
Example:
D14641.06 Codec C90 API Reference Guide TC5.0 November 2011.
© 2010-2011 Cisco Systems, Inc. All rights reserved.
About the API xConfiguration xConfiguration

xConfiguration Video OSD InputMethod Cyrillic

xConfiguration Video OSD LoginRequired

xConfiguration Video AllowWebSnapshots

62
xCommand
Set the Cyrillic mode for the menu input language in the menus on screen.
Requires user role: ADMIN
Value space: <On/Off>
On: Cyrillic mode is available as a menu input language in the menus on screen. This will enable
the setting xConfiguration Video OSD InputMethod InputLanguage.
Off: Cyrillic mode is NOT available as a menu input language in the menus on screen.
Example: xConfiguration Video OSD InputMethod Cyrillic: Off
Determine if the system should require the user to login before accessing the On Screen Display
(OSD). If enabled, the user must enter his username and his PIN. After the user has logged in he can
only execute to the configurations changes and commands allowed by his Role.
ADMIN
Requires user role:
Value space: <On/Off>
On: The user must log in to access the On Screen Display (OSD).
Off: No login to the OSD is required.
Example: xConfiguration Video OSD LoginRequired: Off
Allow or disallow that snapshots captured by the video input main source can be displayed in the web
interface Call Control page.
NOTE: This feature is disabled by default, and must be enabled from the On Screen Display (OSD),
from a directly connected Touch controller, or when connected directly to the serial port (COM 1 port)
on the codec.
Requires user role: ADMIN
Value space: <On/Off>
On: If set to on, a web snapshot can be generated and displayed on the web interface.
Off: The generation of web snapshots is not allowed.
Example: xConfiguration Video AllowWebSnapshots: Off
API Reference Guide
xStatus Appendices
www.cisco.com