Download Print this page

Cisco Codec C90 Installing Manual

Telepresence system
Hide thumbs Also See for Codec C90:

Advertisement

Installing Cisco TelePresence System Codec C90
This box contains:
Codec C90
Top tray
TRC V remote control
A.
Rack profiles (2 pcs)
B.
Rack rear brackets (2 pcs)
C.
Rack extension brackets (2 pcs)
D.
Rack ear profiles left/right (2 pcs)
C
B
A
A
B
Remote Control
D
D
Rack mounting and connecting cables
1
Assembling the rack profiles
Slide the rack profiles A and B together.
LEFT
A
RIGHT
2
Optional: Assembling the extension rails
If the rack is deeper than the length of the
rack profiles A+B, then the extension rails C
are needed.
A+B
78-19811-02 Codec C90 Installation Sheet | December 2012 | © 2010-2012 Cisco Systems, Inc. All rights reserved.
Accessories box and cable kit
HDMI cable (3 m / 10 ft)
Ethernet cable (5 m / 16 ft)
Power cable (1.8 m / 6 ft)
Batteries LR03 AAA 1.5 V for the remote control
Screwdriver, combi 2 mm / 4 mm Allen Key (unbraco)
Screws (M6 and M3) and cage nuts (M6)
Universal rack brackets*
* Universal rack brackets: Use these only if the supplied rail based rack
mounting kit does not fit your type of rack.
User guides
The user documentation for this product, including compliance
and safety information, is available on the Cisco web site.
Go to:
http://www.cisco.com/go/cseries-docs
NOTE:
The profile should
be assembled with the
bend in the direction as
shown in the illustration.
B
B
A
Mount the extension rail (C) to
the rack profiles (A+B) using M6
screws.
Tool: Screwdriver, 4 mm Allen Key
C
C
A+B
Rack mounting
WARRANTY:
Rack mounting the codec without using the
supplied mounting kit will void the warranty.
Please follow the steps in
this installation guide when
rack mounting the codec.
3
Mounting the rack profiles to the rack
Mount the left and right rack profiles A+B(+C) to the rack. The screws,
screwdriver and cage nuts are found in the accessories box.
a)
Mount the rack profiles in front
using two M6 screws on each side.
Tool: Screwdriver, 4 mm Allen Key
b)
Snap the cage
nuts to the rack.
Details in front
NOTE:
If the supplied rack profiles are
incompatible with the rack, use the supplied
universal rack brackets.
Follow the instructions in step 4 on the next page
when assembling the universal rack brackets.
Page 1
TIP
If the menu is not already present,
press Home key or OK key on the
remote control to open the menu.
Navigate in the menu with the
arrow keys.
EMC Class A declaration
声 明
此为A级产品,在生活环境中,该产品可能会造成无线电干扰。在这种
情况下,可能需要用户对其干扰采取切实可行的措施。
WARNING: This is a class A product. In a domestic environment
WARNING:
This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be
this product may cause radio interference in which case the user
required to take adequate measures.
may be required to take adequate measures.
c)
Mount the rack
profiles on the rear
side using the M6
knob screws.
Details viewed from
the rear side
d)
On both sides:
Fasten the rack profiles A+B
together, using one M3 screw on
each side.
Tool: Screwdriver, 2 mm Allen Key

Advertisement

loading

Summary of Contents for Cisco Codec C90

  • Page 1 Follow the instructions in step 4 on the next page each side. when assembling the universal rack brackets. Tool: Screwdriver, 2 mm Allen Key 78-19811-02 Codec C90 Installation Sheet | December 2012 | © 2010-2012 Cisco Systems, Inc. All rights reserved. Page 1...
  • Page 2 (OSD) to this output. On the remote control key in (RJ45 to DSUB) the following sequence: • Disconnect – – – – – – – (where represents DVI-I 2) 78-19811-02 Codec C90 Installation Sheet | December 2012 | © 2010-2012 Cisco Systems, Inc. All rights reserved. Page 2...