List Of Figures - Xantrex XKW 8-350 Operating Manual

List of Figures

Figure 1.1
Figure 1.2
Figure 2.1
Figure 2.2
Figure 2.3
Figure 2.4
Figure 2.5
Figure 2.6
Figure 2.7
Figure 2.8
Figure 2.9
Figure 2.10
Figure 3.1
Figure 3.2
Figure 3.3
Figure 3.4
Figure 3.5
Figure 3.6
Figure 3.7
Figure 3.8
Figure 3.9
Figure 3.10
Figure 3.11
Figure 3.12
Figure 3.13
Figure 3.14
Figure 3.15
Figure 3.16
Figure 3.17
Figure 3.18
Figure 3.19
Figure 3.20
Figure 3.21
Figure 3.22
Figure 3.23
Figure 3.24
Revision A
Power Supply Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Power Supply Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Shipping or Storage Carton Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Stripped Wire Installed in Strain Relief . . . . . . . . . . . . . . . . . . . . . . . . 34
Connector J3 Configuration for Local Operation . . . . . . . . . . . . . . . . . 35
Maximum Load Wire Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Single Load with Local Sensing (Default) . . . . . . . . . . . . . . . . . . . . . . 40
Single Load with Remote Sensing. . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Multiple Loads with Local Sensing. . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Multiple Loads with Remote Sensing. . . . . . . . . . . . . . . . . . . . . . . . . . 42
Local Mode Default Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Connecting Remote Sense Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
J3 Program, Sense, and Monitor Connector Description . . . . . . . . . . 49
Internal Jumpers and Switch (Default Settings Shown). . . . . . . . . . . . 50
Locating Jumpers, Switch, and Connector . . . . . . . . . . . . . . . . . . . . . 51
Programming Output Voltage and Current Limit . . . . . . . . . . . . . . . . . 56
Programming Output Voltage with a 0-5Vdc Source . . . . . . . . . . . . . . 57
Programming Output Voltage with a 0-10Vdc Source . . . . . . . . . . . . . 58
Programming Output Voltage with a 0-1mA Source . . . . . . . . . . . . . . 58
Programming Output Voltage with a 5k ohm Resistance . . . . . . . . . . 59
Programming Output Current Limit with a 0-5Vdc Source. . . . . . . . . . 59
Programming Output Current Limit with a 0-10Vdc Source. . . . . . . . . 60
Programming Output Current Limit with a 0-1mA Source . . . . . . . . . . 61
Programming Output Current Limit with a 5k ohm Resistance . . . . . . 61
Remote Programming of OVP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Remote Programming of OVP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Using Shutdown with a TTL Compatible (Positive Logic) . . . . . . . . . . 66
Using Shutdown with a TTL Compatible (Negative Logic) . . . . . . . . . 66
Using Shutdown with an AC or DC Input (Positive Logic) . . . . . . . . . . 67
Using Shutdown with an AC or DC Input (Negative Logic) . . . . . . . . . 68
Using Shutdown with Contact Closure of a Normally OPEN Relay. . . 69
Using Shutdown with Contact Closure of an OPEN Relay . . . . . . . . . 70
Using Shutdown with Contact Closure of a CLOSED Relay . . . . . . . . 70
Using Shutdown with Contact Closure of a CLOSED Relay . . . . . . . . 71
Series Operation of Multiple Supplies . . . . . . . . . . . . . . . . . . . . . . . . . 74
Parallel Operation of Multiple Supplies . . . . . . . . . . . . . . . . . . . . . . . . 75
xiii