List Of Figures - Xantrex XHR 7.5-130 Operating Manual

List of Figures

Figure 1.1
Figure 1.2
Figure 1.3
Figure 1.4
Figure 1.5
Figure 1.6
Figure 2.1
Figure 2.2
Figure 2.3
Figure 2.4
Figure 2.5
Figure 2.6
Figure 2.7
Figure 2.8
Figure 2.9
Figure 2.10
Figure 3.1
Figure 3.2
Figure 3.3
Figure 3.4
Figure 3.5
Figure 3.6
Figure 3.7
Figure 4.1
Figure 4.2
Figure 4.3
Figure 4.4
Figure 5.1
Figure 5.2
Figure 5.3
Revision A
Power Supply Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Rear Panel with Bus Bar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Rear Panel with High Voltage Output Connector . . . . . . . . . . . . . . . 19
SW1 Programming Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
J2 Programming Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Shipping or Storage Carton Label . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Maximum Load Wire Length for 1 V Line Drop. . . . . . . . . . . . . . . . . 40
Bus Bar Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Typical Load Connection Hardware . . . . . . . . . . . . . . . . . . . . . . . . . 43
Output Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Single Load with Local Sensing (Default) . . . . . . . . . . . . . . . . . . . . . 45
Single Load with Remote Sensing . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Multiple Loads with Local Sensing . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Multiple Loads with Remote Sensing . . . . . . . . . . . . . . . . . . . . . . . . 47
Connecting Remote Sense Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Series Operation of Multiple Supplies. . . . . . . . . . . . . . . . . . . . . . . . 55
Parallel Operation of Multiple Supplies. . . . . . . . . . . . . . . . . . . . . . . 56
Split Supply Operation of Multiple Supplies . . . . . . . . . . . . . . . . . . . 57
Split Supply Operation of Multiple Supplies . . . . . . . . . . . . . . . . . . . 58
Shutdown Programming with Active Low Signal . . . . . . . . . . . . . . . 62
Shutdown Programming with Active High Signal . . . . . . . . . . . . . . . 62
Connecting Programming Sources to J2 Connector . . . . . . . . . . . . 70
Sample Analog Programming Configuration . . . . . . . . . . . . . . . . . . 70
0-5 Vdc Output Voltage and Current Monitoring. . . . . . . . . . . . . . . . 71
0-10 Vdc Output Voltage and Current Monitoring. . . . . . . . . . . . . . . 72
Front Panel Calibration Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Voltage and Current Programming Calibration Locations . . . . . . . . 78
Voltage Current and Monitor Calibration Locations . . . . . . . . . . . . . 80
xi