List Of Figures - Xantrex XFR 2800 Operating Manual

List of Figures

Figure 1.1
Figure 1.2
Figure 1.3
Figure 1.4
Figure 1.5
Figure 1.6
Figure 2.1
Figure 2.2
Figure 2.3
Figure 2.4
Figure 2.5
Figure 2.6
Figure 2.7
Figure 2.8
Figure 2.9
Figure 2.10
Figure 2.11
Figure 2.12
Figure 3.1
Figure 3.2
Figure 3.3
Figure 3.4
Figure 3.5
Figure 4.1
Figure 5.1
Release 2.1
Power Supply Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Power Supply Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Programming and Monitoring SW1 Switch . . . . . . . . . . . . . . . . . . . . . 20
Programming and Monitoring J2 Connector . . . . . . . . . . . . . . . . . . . . 22
Typical Input Current Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . 30
Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Shipping or Storage Carton Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
AC Input Cover and Strain Relief. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Maximum Load Wire Length for 1 V Line Drop . . . . . . . . . . . . . . . . . . 46
Output Strain Relief and Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Typical Load Connection Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Output Voltage Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Single Load with Local Sensing (Default) . . . . . . . . . . . . . . . . . . . . . . 50
Single Load with Remote Sensing. . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Multiple Loads with Local Sensing. . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Multiple Loads with Remote Sensing. . . . . . . . . . . . . . . . . . . . . . . . . . 52
J10 Sense Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Connecting Remote Sense Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Series Operation of Multiple Supplies . . . . . . . . . . . . . . . . . . . . . . . . . 66
Parallel Operation of Multiple Supplies . . . . . . . . . . . . . . . . . . . . . . . . 67
Split Supply Operation of Multiple Supplies. . . . . . . . . . . . . . . . . . . . . 68
Split Supply Operation of Multiple Supplies. . . . . . . . . . . . . . . . . . . . . 69
Connecting Programming Sources to J2 Connector . . . . . . . . . . . . . . 77
Programming and Monitoring Calibration Locations . . . . . . . . . . . . . . 81
xi