Toshiba B-EX4T1 Series Owner's Manual page 101

7. SUPPLY SPECIFICATIONS
B-EX4T-TS12-QM-R
Item
Media pitch
Label length
Tag/Backing paper width
Label width
Gap length
Black mark length (Tag paper)
Max. effective print width
Effective print length
Print speed up/slow down area
Thickness
Maximum effective length for on the fly issue
Maximum outer roll diameter
Roll direction
Inner core diameter
NOTES:
1. To ensure print quality and print head life use only TOSHIBA TEC specified media.
2. When the Rotary Cutter is used, the minimum label length differs depending on the print speed.
* When issuing a label at 3"/sec., label length shall be 91.0 mm – (Gap length/2) or longer.
* When issuing a label at 5"/sec., label length shall be 99.0 mm – (Gap length/2) or longer.
* When issuing a label at 6"/sec., label length shall be 103.0 mm – (Gap length/2) or longer.
* When issuing a label at 8"/sec., label length shall be 110.0 mm – (Gap length/2) or longer.
3. When the Disc cutter is used, the minimum label length shall be 18.0 mm – (Gap length/2) or longer.
4: When using the Rotary Cutter, be sure to install the Ribbon Saving Module (B-EX904-R-QM-R) to perform head-
up and cut. Failure to do this may cause a paper jam or ribbon error.
5: The Rotary Cutter and the Strip Module do not support the print speed of 10"/sec. or faster.
6. When you use tag paper which is narrower than 50 mm, turn the Head Lever to LABEL position.
7. The ratio of a label length to a gap length must be a minimum of 3 to 1 (3:1).
8. When using a label stock in cut mode, be sure to cut the gaps. Cutting labels will cause the glue to stick to the
cutter, which may affect the cutter performance and shorten the cutter life.
Label dispensing mode
Batch mode
Label 10.0 – 1500.0
Tag 10.0 – 1500.0
6.0 – 1498.0
30.0 – 120.0
Label 6.0 – 1496.0
Tag 8.0 – 1498.0
Label
Tag
Strip mode
Head-up disabled
3"/s.: 94.0 - 1500.0
5"/s.: 102.0 – 1500.0
25.4 – 256.0
8"/s.: 113.0 – 1500.0
----
3"/s.: 81.0 – 1494.0
5"/s.: 89.0 – 1494.0
23.4 – 1498.0
8"/s.: 100.0 – 1494.0
50.0 – 120.0
2.0 – 20.0
3"/s.:79.0 - 1492.0
5"/s.: 87.0 – 1492.0
21.4 – 252.0
8"/s.: 98.0 – 1492.0
----
1.0 (Slow down shall be 1.5 when the print speed is 14 ips.)
0.08 – 0.263 (30 to 50 mm width)
Ø200 (Ø180 when using the built-in Rewinder)
Inside (standard)
E7- 2
ENGLISH VERSION EO1-33089
Cut mode
Rotary cutter
Head-up enabled
38.0 – 1500.0
3"/s., 5"/s.: 30.0 – 1500.0
8"/s.: 38.0 – 1494.0
25.0 – 1494.0
30.0 – 120.0
27.0 – 117.0
6.0 – 20.0
2.0 – 10.0
104.0 ±0.2
23.0 – 1492.0
3"/s., 5"/s.: 28.0 – 1498.0
8"/s.: 36.0 – 1498.0
0.08 – 0.17
749.0
Ø76.2±0.3
7.1 Media
[Unit: mm]
Disc cutter
25.4 – 1500.0
25.4 – 1500.0
23.4 – 1494.0
21.4 – 1492.0
21.40 – 1498.0