Table of Contents
Advertisement
Changing Audio Level in an Event
during Event Registration
When registering a new event in a playlist, change the audio
level during the registration of the event.
5
STOP
PLAYER
SOURCE SELECT
PLAY
COUNTER
RESET
REVIEW
1 CLIP PLAY
NEW
TC PRESET
PROP
T
TCG
REGEN
RESET
EXT
TO
UB
DE
UT
CLIP
SHIFT
F3
PF4
1
Assign IN and OUT points to enable event
registration.
2
Use the UNITY/VAR channel selection switch to
select tracks for level setting.
3
Press the PREVIEW button to register the event.
During preview, the audio is output according to the set
level.
4
Use the UNITY/VAR channel selection switch of the
audio fader and fader control during preview
playback to change the level.
After ending or interrupting a preview, the audio level set
so far is reflected and an icon indicating that a level setting
has been made appears on the event on the timeline.
5
Check audio level by performing a review or playlist
playback.
◆ NOTE:
• If the level setting value for all sections in an event is UNITY, the icon
indicating that an event level setting has been made does not
appear.
• If a level setting for an entire playlist has been made for an extended
period of time, a level setting cannot be added and an error is
displayed.
• A level setting for the preroll and postroll playback section cannot
be changed.
106
Editing: Setting Audio Level
3
2,4
PREVIEW
REC
A.LEVEL REC
CONTROL
MODE
REMOTE
LOCAL
STILL/
PAUSE
REW
FF
3
4
1 3
2 4
1
2
PREV
NEXT
UNITY
UNITY
10
0
10
20
30
CH
CH
1/3
2/4
PB
4
• This method for setting the audio level is not available when the
player is a hard disk or an external device.
When an event has been captured to a P2 card, set the audio level.
• Repeating previewing clears the level setting for the preview section
where track selection is available at the start of each preview.
• When a preview is interrupted during the preroll section, the level
setting is not made and the previous level setting is not cleared.
• Pressing the STOP button to interrupt preview makes settings valid
until stopping. Audio level after the interruption point in the event is
set to the same level as the interruption point.
Setting Audio Levels for Specific
Sections
Use the following steps to change the audio level for specific
sections in a playlist.
1
STOP
PLAYER
SOURCE SELECT
PLAY
COUNTER
RESET
REVIEW
1 CLIP PLAY
NEW
TC PRESET
PROP
CH 3
CH 4
TEXT
INT
TCG
MEMO
REGEN
PRESET
EXT
MARKER
VIDEO
A1
A2
GO TO
EDIT MODE
A3
A4
A.DUB
MODE
TRIM
LAST X
SLOT SELECT
DELETE
IN
ENTRY
OUT
SLOT CLIP
ALL CLIP
CLIP LIST
SHIFT
PF1
PF3
PF2
PF4
3
6
1
Press the PLAYER button to switch to recorder
operations.
2
Set the IN point at the location where you want to
start setting the audio level of the recorder and set
the OUT point where you want it to end.
➝Refer to "Setting IN and OUT points" (page 91).
3
Select the track where the audio level will be set.
Select using the A1/A2/A3 (SHIFT + A1)/A4 (SHIFT + A2)
buttons.
4
Press the A LEVEL REC (SHIFT + PREVIEW) button
to start audio level recording/playback.
Playback starts at the beginning of the preroll time section
before the set IN point and stops 1 second later. During
playback of audio level recording, the recorder screen
displays "A LEVEL REC".
4
PREVIEW
REC
A.LEVEL REC
CONTROL
MODE
REMOTE
LOCAL
STILL/
PAUSE
REW
FF
3
4
1 3
2 4
1
2
PREV
NEXT
UNITY
UNITY
10
0
10
20
30
CH
CH
1/3
2/4
PB
5
Advertisement
Table of Contents
