Panasonic AJ-HPM200 Operating Instructions Manual page 91

Limiting the number of clips used as a
player
The player is normally composed of all clips on a P2 card that
conform to the playlist format. Use the steps below to limit the
player to a clip or specific clips.
◆ NOTE:
• Clips not in the playlist format are indicated by red numbers and
cannot be selected for playback.
• This function is not available on external devices.
OFF
METER
FULL/FINE
MONITOR
SELECT
METER SELECT
CH 1-4 CH 5-8
INPUT SELECT
VIDEO AUDIO
CH 1 CH 2 CH 3 CH 4
REC
VAR
UNITY
2
THUMBNAIL PLAYLIST VIDEO A1
5
EDIT MODE A3
TRIM
SET
LAST X
4
MULTI DELETE SLOT SELECT
SEL ENTRY
IN
EXIT MENU
CANCEL/PF DIAG
SLOT CLIP
CLIP LIST
OPERATION
PF1
3
1
Switch to player operation.
Press the PLAYER button to switch to player operation.
2
Display player thumbnails.
During player operation, press the THUMBNAIL button to
display thumbnails on the player screen.
3
Press the MENU button.
4
Use the cursor buttons to select the clip type that
should appear under [THUMBNAIL].
ALL CLIP: Selects all clips
SAME FORMAT Selects clips of the playlist format
CLIPS:
SELECTED Only uses selected clips
CLIPS:
MARKED Selects clips to which shot marks have
CLIPS: been attached
TEXT MEMO Selects clips with text memos
CLIPS:
SLOT CLIPS: Selects clips on P2 card in slot No. n
1
PREVIEW
STOP REC A.LEVEL REC
PLAYER
STILL/
SOURCE SELECT
PLAY PAUSE REW FF
COUNTER
RESET
REVIEW PREV NEXT
1 CLIP PLAY
NEW
TC PRESET
PROP
TEXT
INT
TCG
MEMO
REGEN
PRESET
EXT
MARKER
A2 GO TO
A4 A.DUB
MODE
OUT
ALL CLIP
SHIFT
PF2 PF3
PF4
◆ NOTE:
• To select specific clips as a player, select clips to be used from
the player thumbnails and select [SELECTED CLIPS]. The clips
then appear in the order they were selected.
• Each press of the SLOT CLIP (SHIFT + IN) button switches the
clip in the following order SELECTED ➝ SLOT1 ➝
SLOT2...SLOT6 ➝ SELECTED (only slots with cards).
• Press ALL CLIP (SHIFT + OUT) to switch to ALL CLIP.
5
Press the SET button.
The player screen opens and the player will now only use
the selected clips.
Setting IN and OUT points
1
OFF
METER
FULL/FINE
MONITOR
SELECT
METER SELECT
CH 1-4 CH 5-8
INPUT SELECT
VIDEO AUDIO
CH 1 CH 2 CH 3
REC
VAR
UNITY
PLAYLIST VIDEO
THUMBNAIL
EDIT MODE
SET LAST X
MULTI DELETE
SEL IN
EXIT MENU
CANCEL/PF DIAG
SLOT CLIP
OPERATION
PF1
4,5,7,8
1
Selecting insert or overwrite editing.
Use the EDIT MODE (SHIFT + VIDEO) button to select
insert or overwrite editing.
2
Select tracks.
Use the VIDEO/A1/A2/A3/A4 buttons to select the tracks
that should be imported. The names of selected tracks are
indicated in yellow on the left side of the timeline.
3
Switch to player operation.
Press the PLAYER button to switch to player operation.
4
Set the IN point of the player.
While looking at the player screen, hold down the IN button
and press the ENTRY button at the start location of the
required section to set the player IN point. A green
added to the player bar. The time code of the set IN point
appears on the player screen while the IN button is held
down.
2 3,6
STOP
PLAYER
STILL
SOURCE SELECT
PLAY PAUS
COUNTER
RESET
REVIEW
1 CLIP PLAY
NEW
TC PRESET
PROP
CH 4
TEXT INT
TCG
MEMO
REGEN
PRESET
EXT
MARKER
A1 A2 GO TO
A3 A4 A.DUB
MODE
TRIM
SLOT SELECT
ENTRY OUT
ALL CLIP
CLIP LIST
SHIFT
PF2 PF3
PF4
1
Editing: Creating Playlists
is
91