Error Messages - Steinberg MR816CSX Operation Manual

Functions
Analog Input
MIC Preamp
[+48V] button
(Phantom Power switch)
[PAD] button
Gain knob
Input Channels 1 – 8
Phase
High Pass Filter
[HI-Z] switch
AD converter
[SIG/PEAK] lamp
Analog Output
Output Channels 1 – 8 Level Control
DA converter
Level Control
Headphone jacks
1 and 2
Maximum Output Level
IEEE1394 jack Audio interface
* Specifications and descriptions in this Operation Manual are for information purposes only. Steinberg/Yamaha reserves the
right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or
options may not be the same in every locale, please check with your Steinberg/Yamaha dealer.
European models
Purchaser/user Information specified in EN55103-1 and EN55103-2.
Inrush current: 2.0 A (MR816 CSX), 2.0 A (MR816 X)
Conforms to environments: E1, E2, E3, E4

Error Messages

Error message
Failed to initialize.
(Software name) (Version) is
installed. Yamaha Steinberg
FW Driver cannot work with
this version. Please update it
to V1.6.3 or later.
Failed to open Control
Panel.
Failed to change driver
setting due to another
processing.
Failed to change driver
setting.
* The Word Clock source lamps and Sample Rate lamps flash in order when the MR816 CSX/MR816 X is not recognized by the
computer.
Discrete Class-A MIC preamp (Inverted Darlington Circuitry)
+48 V DC
0/26 dB
44 dB variable (-60 dB to -16 dB)
Normal/Reversed (controlled via a computer)
OFF/80 Hz (-12 dB/oct.)
Controlled via a computer
On/off (for channel 1), Input impedance: 500 kΩ
24 bit linear, Enhanced dual-bit delta-sigma conversion
-3dB or mode (red), -40db – -3dB (green) (when the clipping point of the signal
is assumed to be 0 dB)
Multi Function Encoder knob control (for all the channels 1 – 8)
Software control (for each of the channels 1 – 8)
24 bit linear, 128 times oversampling Advanced multi-bit delta/sigma conversion
Multi Function Encoder knob control
25mW (@ 8Ω)/75mW (@ 40Ω)
16-ch input/16-ch output
Cause
Initialization of Yamaha Steinberg FW Driver has
failed.
(Windows only)
The version of Yamaha n Driver, Yamaha AI Driver
and mLAN Driver/mLAN Tools installed to your
computer may not be compatible with the Yamaha
Steinberg FW Driver.
The Yamaha Steinberg FW Driver does not work
properly.
The settings on the Control Panel cannot be
accepted because another program is now
changing the settings of the Yamaha Steinberg
FW Driver.
Failed due to a cause other than the above.
Insufficient memory space.
Solution
Restart the computer.
Update mLAN Driver/mLAN Tools installed to your
computer to V1.6.3 or later.
Uninstall Yamaha AI Driver or Yamaha n Driver
(Use Yamaha Steinberg FW Driver or mLAN
Driver/mLAN Tools instead).
Try the following operations.
· Restart the computer.
· Uninstall then install TOOLS for MR
Perform the settings again after a while.
When a specific device is not recognized by
the computer*:
Disconnect the IEEE1394 cable from the unrecog-
nized device then connect again or turn off the
power to that device then turn on the power again.
When all the connected devices are not recog-
nized by the computer*:
Restart the computer.
Exit all unnecessary applications and uninstall the
unnecessary drivers.
Operation Manual
Appendix
49