Table of Contents
Advertisement
Keyswitch Sensor (0015)
This feature lets users arm and disarm the system using either a keyswitch wired
to a hardwire zone input or a wireless door or window sensor.
For example, if sensor 1 is designated as the keyswitch sensor and the system is
disarmed, then tripping sensor 1 arms the system to AWAY. If the system is armed
to STAY or AWAY, tripping sensor 1 disarms the system. The panel reports open-
ing, closing, and force armed reports (if these features are turned on) to the cen-
tral monitoring station.
Note
A bypassed keyswitch sensor cannot arm or disarm the system.
During an audible alarm, keyswitch sensors can disarm the system (which sends a
cancel report to the central monitoring station), but cannot arm the system. The system
can be armed only after siren timeout expires.
Keyswitch sensors test the same as any other sensor and do not arm or disarm the
system during a sensor test.
Duress Code (0016)
The duress code is a unique 4-digit access code that allows users to operate
the system and, at the same time, instructs the panel to send a silent alarm
report to the central station.
Do not use a duress code unless it is absolutely necessary. Using duress
codes often results in false alarms due to code entry errors. If a duress code
is absolutely necessary, use it with an Interrogator
ule (AVM) to reduce false alarms and accidental dispatches.
Note
To use this feature, the Duress Option setting under the
PARTITION 1
menu must be turned on.
Phone Number (0100-cs phone 1,
0110-cs phone 2)
(Default = none) This setting is used for pro-
gramming the central station receiver phone
number. Phone numbers can be 1-24 digits
long, including pauses or * and # characters. To
enter pauses, press C . To enter *, press and
hold 7 for one second. To enter #, press and
hold 9 for one second.
Note
PHONE NUMBER
The
menus are not accessible if a
Dealer Code is programmed and the Installer
Code is used to enter installer programming mode.
To access these menus when a Dealer Code is
programmed, you must enter installer program-
ming mode using the Dealer Code.
A phone number must be programmed for UL
1635 listed installations.
23
®
audio verification mod-
REPORTING—
Phones Menu
The
menu lets you set up central station reporting for the system (global) and pager
PHONES
reports (partition specific). The following describes how to program the settings that appear
under
.
CS PHONE 1-2
¾
To program a Central Station Phone Number:
1. With the display showing
desired phone number. The display flashes the entered number.
2. Press ƒ and the display shows the new number.
Note
Call-waiting services should be disabled to prevent interruptions to panel communi-
cation to the central monitoring station (or pager). To program a dialing prefix that
disables call-waiting, see the Call Wait Cancel setting under the menu
OPTIONS—GLOBAL
¾
To delete a Central Station Phone Number:
1. With the display showing
The display shows
Security-Partition 1 (Default = none)
¾
To assign a Keyswitch Sensor:
1. With the display showing
SENSOR n
the desired sensor number (01-24). The
display flashes the entered sensor num-
ber.
2. Press ƒ and the display shows the new
number.
Security-Partition 1 (Default = none)
¾
To program a Duress Code:
1. With the display showing
, enter the desired 4-digit duress code.
****
The display flashes the entered setting.
2. Press ƒ and the display shows the new
code.
¾
To delete a Duress Code:
1. With the display showing
(current code), press D . The display
nnnn
shows
DURESS CODE ****
Phones-CS Phone 1-2 (Default = none)
PHONE NUMBER _
.
PHONE NUMBER n
.
PHONE NUMBER _
KEYSWITCH
(current sensor number), enter
DURESS CODE
DURESS CODE
.
(or current number), enter the
PHONE
(current number), press D .
Programming the Panel
Hide quick links:
Advertisement
Table of Contents
