Keypad Mode (P1-12 = 1 Or 2) - Invertek Drives Optidrive Plus 3GV User Manual

7.2. Keypad mode (P1‐12 = 1 or 2)
P2‐01 Digital input 1 (T2)
Open: Stop (disable)
0
Closed: Run (enable)
Open: Stop (disable)
1
Closed: Run (enable)
Open: Stop (disable)
2
Closed: Run (enable)
3..9, 13, Open: Stop (disable)
14 & 16 Closed: Run (enable)
Open: Stop (disable)
10
Closed: Run (enable)
Open: Stop (disable)
11
Closed: Run (enable)
Open: Stop (disable)
12
Closed: Run (enable)
Open: Stop (disable)
15
Closed: Run (enable)
Open: Stop (disable)
17
Closed: Run (enable)
Open: Stop (disable)
18
Closed: Run (enable)
Open: Stop (disable)
19
Closed: Run (enable)
Open: Stop (disable)
20, 21
Closed: Run (enable)
Open: Stop (disable)
22
Closed: Run (enable)
By default, if the enable signal is present the drive will not Enable until the
when the enable signal is present set P2‐19 = 2 or 3. This then disables the use of the
In keypad mode, the speed can be adjusted using the
keypad, in addition to pushbuttons connected to the digital inputs
The reverse input only functions under the following conditions :‐
•
P1‐12 = 1, P2‐19 = 2 or 3. P2‐35 must not be 2 or 3
NOTE
•
P1‐12 = 2. P 2‐35 must not be 2 or 3
The external trip input can be used to connect a motor thermistor by connecting between terminals 1 and 4
When P1‐12 =2, the direction of motor can be reversed by
•
pressing the
•
Closing the reverse input (When using a setting of P2‐01 that inlcuides this function)
•
Using a negative speed reference (e.g. select a preset speed of ‐10Hz)
Since all of these functions can be active at once, care must be taken to ensure the motor always turns in the correct direction.
GV
Optidrive Plus 3 User Guide
www.invertek.co.uk
Digital input 2 (T3)
Closed : remote UP push‐button Closed : remote DOWN push‐button
When stopped, closing inputs 2 & 3 simultaneously starts the drive
Closed : remote UP push‐button
Closed : remote UP push‐button
Closed : remote UP push‐button Closed : remote DOWN push‐button
When stopped, closing inputs 2 & 3 simultaneously starts the drive
Open : Digital speed ref
Closed : Bipolar analog speed ref
Open : Digital speed ref
Closed : Preset speed 1
Open : Preset speed 1
Closed : Digital speed ref
Open : Digital speed ref
Closed : Preset speed 1
Open : Digital speed ref
Closed : Bipolar analog speed ref
Open : Digital speed ref
Closed : Preset speed ref
Open : Digital speed ref
Closed : Analog input 2 ref
Digital Output :
Drive Healthy = +24V
Digital Output :
Drive Healthy = +24V
button
Digital input 3 (T4)
External trip input :
Open: Trip,
Closed: No Trip
Open: Digital speed ref
Closed: Preset speed 1
External trip input
Open: Trip,
Closed: No Trip
External trip input
Open: Trip,
Closed: No Trip
External trip input
Open: Trip,
Closed: No Trip
Open: Decel Ramp 1 (P1‐04)
Closed: Decel Ramp 2 (P2‐25)
Open : Digital / Analog ref
Closed : Preset speed 1
Digital Input 3
Open Open
Closed Open
Open Closed
Closed Closed
Analog input 2
Open : Digital speed ref
Closed : Preset speed 1
External trip input
Open: Trip,
Closed: No Trip
button is pressed. To automatically enable the drive
& keys on the built in keypad, or a remote mounted Optiport Plus
Bipolar analog input (T6)
No Function
Closed : remote DOWN push‐
button
Open : Forward
Closed : Reverse
Open : Forward
Closed : Reverse
Bipolar analog input
Open : Forward
Closed : Reverse
Open : Forward
Closed : Reverse
Open : Forward
Closed : Reverse
Bipolar analog input
Bipolar analog input Preset reference
Preset Speed 1
Preset Speed 2
Preset Speed 3
Preset Speed 4
Open : Forward
Closed : Reverse
Open : Forward
Closed : Reverse
Open : Forward
Closed : Reverse
& STOP buttons
23