Control Terminal Connections - Invertek Drives Optidrive Plus 3GV User Manual

4.7. Control terminal connections
Default Connections
4.8. Electromagnetic Compatibility
All Optidrives are designed to high standards of EMC and can optionally be fitted with an internal EMC filter. This EMC filter is designed to reduce
the conducted emissions back into the supply via the power cables for compliance with harmonised European standards.
It is the responsibility of the installer to ensure that the equipment or system into which the product is incorporated complies with the EMC
legislation of the country of use. Within the European Union, equipment into which this product is incorporated must comply with 89/336/EEC,
EMC. When using the internal or optional external filter, the following maximum motor cable lengths apply:‐
EMC Category C1
Drive Frame Size
230 Volt, Single Phase Input
Size 1 1m
Size 2 1m
3 Phase, 400 Volt Input
Size 2 5m
Size 3 5m
Size 4 5m
Size 5 5m
Size 6 5m
For motor cable lengths greater than 100m, an output dv / dt filter must be used, please refer to the Invertek Stock Drives Catalog
for further details
For Size 5 and 6 drives, ferrite ring must be installed on the output motor cable, with all three phases of the motor cable being
Note
wrapped one turn around the ferrite ring.
Vector Speed and Torque control modes may not operate correctly with long motor cables and output filters. It is recommended to
operate in V/F mode only for cable lengths exceeding 50m
GV
Optidrive Plus 3 User Guide
www.invertek.co.uk
Control Terminal Signal
+24V User
1
Output,
2 Digital Input 1
Digital Input 2 /
3
Digital Output 3
Digital Input 3 /
4
Analog Input 2
5 +24V User Output
Bipolar analog
6 Input /
Digital Input 4
7 0V
Analog Output /
8
Digital Output
9 0V
10 Relay Common
11 Relay NO Contact
Screened Motor Cable Length
With Internal Filter
C2
5m
5m
25m
25m
25m
25m
25m
Description
+24V, 100mA user control output
Positive logic
"Logic 1" input voltage range: 8V ... 30V DC
"Logic 0" input voltage range: 0V ... 8V DC
Input : Positive logic
"Logic 1" input voltage range: 8V ... 30V DC
"Logic 0" input voltage range: 0V ... 8V DC
Output : 24V 10mA Max 'Drive Healthy' Output
Digital : "Logic 1" input voltage range : 8 to 30V DC
"Logic 0" input voltage range : 0 to 8 V DC
Analog: 0 to 10V, 0 to 20mA or 4 to 20mA
+24V, 100mA, 1kΩ minimum
Digital : "Logic 1" input voltage range : 8 to 30V DC
"Logic 0" input voltage range : 0 to 8 V DC
Analog: 0 to 24V, 0 to 10V, ‐10 to +10V, ‐24 to + 24V
User ground, connected to terminal 9
Analog: 0 to 10V DC, 10 to 0 V DC, 20mA Maximum
4 to 20mA, 20 to 4 mA
Digital: 0 to 24V DC, 20mA Maximum
User ground, connected to terminal 7
Volt free contacts. Maximum load should not exceed
250Vac, 6A / 30Vdc, 5A
C3 C1
25m 25m
25m 50m
50m 50m
50m 50m
50m 50m
50m 50m
50m 50m
With External Filter
C2
50m 100m
100m 200m
100m 200m
100m 200m
100m 200m
100m 200m
100m 200m
C3
11