Keypad Mode (P1-12 = 1 Or 2); User Pi Control Mode (P1-12 = 3) - Invertek Drives Optidrive Plus 3GV Compact User Manual

7.2. Keypad mode (P1-12 = 1 or 2)

P2-01 Digital input 1 (T2)
Open: Stop (disable)
0
Closed: Run (enable)
Open: Stop (disable)
1
Closed: Run (enable)
Open: Stop (disable)
2
Closed: Run (enable)
3..9, 13, Open: Stop (disable)
14 & 16 Closed: Run (enable)
Open: Stop (disable)
10
Closed: Run (enable)
Open: Stop (disable)
11
Closed: Run (enable)
Open: Stop (disable)
12
Closed: Run (enable)
Open: Stop (disable)
15
Closed: Run (enable)
Open: Stop (disable)
17
Closed: Run (enable)
Open: Stop (disable)
18
Closed: Run (enable)
Open: Stop (disable)
19
Closed: Run (enable)
Open: Stop (disable)
20, 21
Closed: Run (enable)
Open: Stop (disable)
22
Closed: Run (enable)
By default, if the enable signal is present the drive will not Enable until the By default, if the enable signal is present the drive will not Enable until the
enable signal is present set P2-19 = 2 or 3. This then disables the use of the
In keypad mode, the speed can be adjusted using the In keypad mode, the speed can be adjusted using the
NOTE
addition to pushbuttons connected to the digital inputs addition to pushbuttons connected to the digital inputs
The reverse input only functions under the following conditions The reverse input only functions under the following conditions
-
P1-12 = 1, P2-19 = 2 or 3. P2-35 must not be 2 or 3
- P1-12 = 2. P 2-35 must not be 2 or 3
The external trip input can be used to connect a motor thermistor by connecting the thermistor between terminals 1 and 4 The external trip input can be used to connect a motor
7.3. User PI control mode (P1-12 =
P2-01 Digital input 1 (T2)
0..10,
Open: Stop (disable)
13..16,
Closed: Run (enable)
18
Open: Stop (disable)
11
Closed: Run (enable)
Open: Stop (disable)
12
Closed: Run (enable)
Open: Stop (disable)
17
Closed: Run (enable)
Open: Stop (disable)
19
Closed: Run (enable)
Open: Stop (disable)
20, 21
Closed: Run (enable)
Open: Stop (disable)
22
Closed: Run (enable)
When P3-05 = 1, Bipolar analog input controls PID setpoint
NOTE (Default setting)
The external trip input only functions when the feedback source is the Bipolar analog input The external trip input only functions when the feedback source is the Bipolar analog input (P3-10 = 1)
Optidrive Plus 3
2)
Digital input 2 (T3) Digital input 2 (T3)
Closed : remote UP push-button Closed : remote UP push
Closed : remote UP push Closed : remote UP push-button
Closed : remote UP push Closed : remote UP push-button
Closed : remote UP push Closed : remote UP push-button
Open : Digital speed ref Open : Digital speed ref
Closed : Bipolar analog speed ref Closed : Bipolar analog speed ref
Open : Digital speed ref Open : Digital speed ref
Closed : Preset speed 1 Closed : Preset speed 1
Open : Preset speed 1 Open : Preset speed 1
Closed : Digital speed ref Closed : Digital speed ref
Open : Digital speed ref Open : Digital speed ref
Closed : Preset speed 1 Closed : Preset speed 1
Open : Digital speed ref Open : Digital speed ref
Closed : Bipolar analog speed ref Bipolar analog speed ref
Open : Digital speed ref Open : Digital speed ref
Closed : Preset speed ref Closed : Preset speed ref
Open : Digital speed ref Open : Digital speed ref
Closed : Analog input 2 ref Closed : Analog input 2 ref
No Function
No Function
19 = 2 or 3. This then disables the use of the
35 must not be 2 or 3
12 = 3)
Digital input 2 (T3)
No Function No Function
Open : PID control Open : PID control
Closed : Preset speed 1 Closed : Preset
Open : Preset speed 1 Open : Preset speed 1
Closed : PID control Closed : PID control
Open : PID Control Open : PID Control
Closed : Bipolar analog ref Closed : Bipolar analog ref
Open : PID Control Open : PID Control
Closed : Analog input 2 ref Closed : Analog input 2 ref
No Function No Function
No Function No Function
analog input controls PID setpoint. The feedback must then be connected to Analog input 2
www.invertek.co.uk
GV
Compact - User Guide
Analog Input 1 (T4)
(or Digital Input 3)
No Function
Closed : remote DOWN push-button
Open : Forward
Closed : Reverse
Open : Forward
Closed : Reverse
Bipolar Analog Input
Open : Forward
Closed : Reverse
Open : Forward
Closed : Reverse
Open : Forward
Closed : Reverse
Bipolar Analog Input
Digital Input 3
Open
Open
Closed
Closed
Open : Forward
Closed : Reverse
Open : Forward
Closed : Reverse
Open : Forward
Closed : Reverse
button is pressed. To automatically enable the drive when the button is pressed. To automatically enable the drive when the
& buttons
& keys on the built in keypad, or a remote mounted Optiport Plus keypad, in keys on the built in keypad, or a remote mounted Optiport Plus
by connecting the thermistor between terminals 1 and 4
Analog Input 1 (T4)
(or Digital Input 3)
Bipolar Analog Input
Bipolar Analog Input
Bipolar Analog Input
Bipolar Analog Input
Bipolar Analog Input
Bipolar Analog Input
Bipolar Analog Input
The feedback must then be connected to Analog input 2 and P3-10 must be set to 0
Analog input 2 (T4)
(or Digital Input 4)
Closed : remote DOWN push-button
External trip input :
Open: Trip,
Closed: No Trip
Open: Digital speed ref
Closed: Preset speed 1
Closed : remote DOWN push-button
External trip input :
Open: Trip,
Closed: No Trip
External trip input :
Open: Trip,
Closed: No Trip
External trip input :
Open: Trip,
Closed: No Trip
Open: Decel Ramp 1 (P1-04)
Closed: Decel Ramp 2 (P2-25)
Open : Digital / Analog ref
Closed : Preset speed 1
Digital Input 4 Digital Input 4 Preset reference
Open Preset Speed 1
Closed Preset Speed 2
Open Preset Speed 3
Closed Preset Speed 4
Analog input 2
Open : Digital speed ref
Closed : Preset speed 1
External trip input :
Open: Trip,
Closed: No Trip
Analog input 2 (T4)
(or Digital Input 4)
Analog input 2
External trip input :
Open: Trip,
Closed: No Trip
External trip input :
Open: Trip,
Closed: No Trip
Analog input 2
Analog input 2
Analog input 2
External trip input :
Open: Trip,
Closed: No Trip
19