Extron electronics IPL EXP Series User Manual page 47

Command Function
IP setup commands, IPv6
IPv6 is disabled by default but can be enabled and configured via SIS commands. The IPL EXP Control System Power Expansion
Interfaces supports dual stack (the ability to use both IPv4 and IPv6). You can set either or both IP protocols active at any point in time.
NOTE:
While IPv4 is disabled, the unit cannot be accessed and controlled via Extron software.
Ethernet access (IPv4 and IPv6)
Disable IPv4 network access
Enable IPv4 network access
View IPv4 status
Disable IPv6 network access
Enable IPv6 network access
View IPv6 status
Enable network access
24
Disable network access
24
View network access setting
NOTES:
•
A network restart (2BOOT command) is required for IP version changes to be applied.
•
Firmware prevents disabling both IPv4 and IPv6. If IPv6 is turned off, then IPv4 turns on and vice-versa. An unsolicited message showing
the changed setting will appear when the IP version is changed.
•
If the device (NIC) does not support IPv6 then IPv4 cannot be disabled and IPv6 cannot be enabled with the
If a NIC does not support IPv6, the unit issues an E14 error. This could potentially happen if the unit has a firmware version older than
v1.01.0000-b026.
DHCP status and modes in IPv6
Disable DHCP (turn it off, use a
static IP address), IPv6
24
Enable DHCP (turn it on,
use an automatically assigned
IP address), IPv6
24
Set DHCP mode (IPv6)
24
View DHCP mode (IPv6)
NOTE: A network restart (2BOOT command) is required for DHCP changes to be applied.
Address generation mode in IPv6
Select EUI-64
24
Select stable privacy mode
View address generation mode
NOTE: If IPv6 is enabled in Extron devices, the device generates an EUI-64 address based on its MAC address.
00-05-A6-xx-yy-zz
For a MAC address of
fe80::205:a6ff:feXX:YYZZ /64
The EUI-64 address provides a predictable unit address for access from PC to device while they are on the same subnet.
X8#
KEY: = Enabled/disabled status
X57^
= NIC number
X59#
= DHCP modes
SIS Command
(Host to Unit)
X57^ *4*0 ETHN }
E
V
E X57^ *4*1 ETHN }
V
E X57^ *4 ETHN }
V
E X57^ *6*0 ETHN }
V
E X57^ *6*1 ETHN }
V
E X57^ *6 ETHN }
V
E }
E 1 * 1 ETHN
E }
E 1 * 0 ETHN
E }
E 1 ETHN
EX57^ *0 DHCP6 }
EX57^ *1 DHCP6 }
EX57^ * X59# DHCP6 }
EX57^ DHCP6 }
E A X57^ *0 ETHN }
E A X57^ *1 ETHN }
24
E A X57^ ETHN }
, the IPv6 Link Local address is:
.
0
= disabled,
1-3
. For the IPL EXP, the NIC (Network Interface Card) is
to the product, the unit returns an E13 error code.
0
= static (and link-local) addresses
1
= automatic (DHCPv6, SLAAC, and link-local) addresses (default)
2
= Use DHCPv6 (and link-local) addresses.
3
= Use SLAAC (and link-local) addresses. Use DHCPv6 for DNS information.
4
= Use SLAAC (and link-local) addresses.
5
= Use only the link-local address.
IPL EXP Power Series • Modes of Operation, SIS Control and Configuration
Response
(Unit to Host)
X57^ *4*0 ]
EthnV
X57^ *4*1 ]
EthnV
X8# ]
X57^ *6*0 ]
EthnV
X57^ *6*1 ]
EthnV
X8# ]
EthnE ]
1 * 1
EthnE ]
1 * 0
X8#]
X57^ *0 ]
Dhcp6•
X57^ *1 ]
Dhcp6•
X57^ * X59# ]
Dhcp6•
X59# ]
X57^ *0 ]
EthnA
X57^ *1 ]
EthnA
address-generation
<
mode ]
>
1
= enabled
Additional Description
Network access is enabled by default.
V ETHN
commands.
0
= eui64 (default),
1
= stable-privacy
1
. If a NIC number is not applicable
37