Lenovo ThinkSystem SD550 V3 User Manual page 208

3. If necessary, install the power distribution board and connect cables between the power distribution
board and the system board (see
distribution board cable routing" on page
4. Reinstall the power bus bar (see
5. If necessary, reinstall the PCIe riser assembly to the node and reconnect the required PCIe cables to the
system board (see "Install a PCIe riser assembly" on page 154
223).
6. Reinstall the fan cage to the node and reconnect all the fan cables to the system board (see
cage" on page 109).
7. If necessary, reinstall the GPU air duct (see
8. If necessary, reinstall the internal adapter bracket and reconnect all the required cables to the internal
adapter (see "Install an internal adapter bracket" on page 129
routing" on page 215
9. Reinstall the required M.2 drives to the system board (see
10. Reinstall the MicroSD card to the system board (see
11. Reinstall the firmware and RoT security module to the system board (see
security module" on page
12. Reinstall all the required memory modules or memory module fillers (see
page 137).
13. If there is no CMOS battery (CR2032) installed on the system board yet, install one (see
battery (CR2032)" on page
14. Reconnect all the required cables to the system board (see
211).
15. Reinstall the required front or rear air baffle (see
16. Reconnect all the required cables to the drive backplane; then, reinstall the drive cage assembly to the
node (see "2.5-inch drive backplane cable routing" on page 215
page 101).
17. If necessary, reinstall the flash power module and reconnect the flash power module cable (see
flash power module" on page
18. Reinstall all drives and drive fillers (if any) to the node (see
19. Reinstall the required processor and heat sink modules (PHMs) (see
on page 171).
20. If necessary, install the rear air baffle (see
21. Make sure that all the required cables are routed and connected correctly; then, reinstall the top cover
(see "Install the top cover" on page
22. Reinstall the node into the chassis (see
23. Make sure that the required power supply units are installed and power cords are connected; then,
power on the node (see
53.)
24. Proceed to complete the parts replacement (see
25. Update the vital product data (VPD). See
type number and serial number can be found on the ID label, see
Lenovo XClarity Controller" on page
26. If hiding TPM or updating TPM firmware is needed, see
the TPM firmware" on page
27. Optionally, enable UEFI Secure Boot. See
ThinkSystem SD550 V3 User Guide
198
"Install a power distribution board" on page 163
225).
"Install a power bus bar" on page
"Install a GPU air duct" on page
).
188).
94).
112).
"Install an air baffle" on page
205).
"Install a node to the chassis" on page
"Install a hot-swap power supply" on page 63
"Update the Vital Product Data (VPD)" on page
37.
201.
"Enable UEFI Secure Boot" on page
159).
and "PCIe riser cable routing" on page
and "2.5-inch drive backplane cable
"Install an M.2 drive" on page
"Install a MicroSD card" on page
Chapter 6 "Internal cable routing" on page
"Install an air baffle" on page
and "Install a drive cage assembly" on
"Install a hot-swap drive" on page
"Install a processor and heat sink"
85).
and
"Complete the parts replacement" on page
"Identify the system and access the
"Hide/observe TPM" on page 200
and "Power
"Install a fan
121).
133).
142).
"Install a firmware and RoT
"Install a memory module" on
"Install a CMOS
85).
"Install a
124).
78).
"Power on the node" on page
208).
199. Machine
or "Update
202.