Nailor 35SW Manual

DESCRIPTION:
• 18 ga. (1.31) galvanized steel
channel frame with 20 ga.
(1.00) casing components.
• 16 ga. (1.61) galvanized steel
inclined opposed blade damper.
45° rotation. CW to close.
• Ultra-high efficiency ECM
fan motor. EPIC fan volume
controller.
• Multi-point averaging
Diamond Flow sensor. Supplied
with balancing tees.
• Full size access panels on
three sides.
• 3/4" (19) dual density
insulation, exposed edges
coated to prevent air erosion.
Meets requirements of NFPA
90A and UL 181.
• Single point electrical and /or
pneumatic main air connection.
• Discharge opening for flanged
duct connection.
• Full primary air valve low
voltage NEMA 1 type enclosure
for factory mounted DDC and
analog electronic controls.
• Controls mounted as
standard on RH side as shown.
Terminals ordered with LH
controls (optional) are inverted
and discharge duct hanging
elevation will therefore change.
OPTIONS:
Digital Controls:
q
Factory mounted (supplied
by others)
q
Field mounted (supplied by
others)
q
Nailor EZvav. See separate
submittal.
Liner:
q
Steri-liner
q
Steri-liner + Perforated metal
q
Fiber-free
q
Perforated metal
q
Solid metal
q
1" (25) fiberglass
q
Low temperature
construction
Other:
q
Left-hand controls location
q
Toggle disconnect switch
q
Fan unit fusing
q
24/24V Isolation transformer
q
Cross Flow Sensor
q
'Q' Option – Induced Air
Inlet Attenuator
q
Top entry induced air inlet
q
1" (25) Throwaway
q
2" (51) Filter rack only
q
Hanger brackets.
q
1/4-turn fasteners (access
panel)
q
FN2 90° Line Voltage
Enclosure
SCHEDULE TYPE:
PROJECT:
ENGINEER:
CONTRACTOR:
Nailor Industries Inc. reserves the right to change any information concerning product or pricing without notice.
FAN POWERED TERMINAL UNIT WITH
EPIC ECM MOTOR
SERIES FLOW • CONSTANT OR VARIABLE VOLUME
MODELS: 35S, 35SW AND 35SE • UNIT SIZES 1 – 6
Model 35S • Basic Unit
PRIMARY
AIR
MULTI-POINT
FLOW SENSOR
DRIVESHAFT
5 1/2"
(140)
OPTIONAL
PRIMARY PRIMARY
11"
AIR VALVE
(279)
CONTROLS
AIR
H
ENCLOSURE
2
Dimensional Data
Unit Inlet
W W2
Size Size
5, 6, 8** 20
1
(127, 152, 203) (508) (889)
6, 8 18
2
(152, 203) (457) (838)
6, 8, 10, 12 18
3
(152, 203, 254, 305) (457) (838)
8, 10, 12, 14 26
4
(203, 254, 305, 356) (660) (1041)
10, 12, 14 26
5
(254, 305, 356) (660) (1041)
12, 14, 16 30
6
(305, 356, 406) (762) (1143)
**
ECM Only.
q
FN3 Remote Line Voltage Controls Enclosure
(See submittal FN3)
q
Dust tight enclosure seal
q
Remote user disconnect
Seismic Certification:
q
Seismic Source International (Standard)
q
HCAI (formerly OSHPD, California)
q
Special Features: _________ .
Listed
L
IW + 2" (51)
INDUCED
AIR
IH +
2" (51)
W
2
OPTIONAL
TOP
TW
INLET
HINGED FAN
CONTROLS
TL
ENCLOSURE
5 3/4"
5 3/4"
(146)
(146)
14" (356)
OPTIONAL
90° FN2
CONTROLS
ENCLOSURE
HINGED FAN H -
1" (25) H
CONTROLS
ENCLOSURE
Induced Air Inlet
H L B
Side (std.)
IW x IH
35 14 36 6 8 x 10
(356) (914) (152) (203 x 254)
33 14 36 3 1/2 8 x 10
(356) (914) (89) (203 x 254)
33 18 36 3 1/2 12 x 14
(457) (914) (89) (305 x 356)
41 18 41 6 14 x 14
(457) (1041) (152) (356 x 356)
41 18 41 5 14 x 14
(457) (1041) (127) (356 x 356)
45 19 44 6 16 x 15
(483) (1118) (152) (406 x 381)
Electrical Data
*
FLA = Full load amperage. All motors are single
phase/60 Hz.
Page 1 of 2. For heat options; see page 2.
DATE
2 - 6 - 23
'Q' OPTION
INDUCED
AIR
OPTIONAL
ATTENUATOR
FILTER
FAN
W
DH
1" (25)
15"
(381)
6 3/4"
(171)
14" (356)
(203)
OPTIONAL
INDUCED AIR IH
INLET FILTER
IW
Outlet
Discharge
Top (opt.) Side Inlet
DW x DH
TL x TW
10 x 14 8 1/8 x 4 1/4
(254 x 356) (206 x 108) (254 x 305)
10 x 14 9 1/4 x 10 1/2
(254 x 356) (235 x 267) (254 x 305)
14 x 14 9 1/4 x 10 1/2
(356 x 356) (235 x 267) (356 x 406)
12 x 22 12 x 10 1/2
(305 x 559) (305 x 267) (406 x 406)
12 x 22 13 1/4 x 11 1/2
(305 x 559) (337 x 292) (406 x 406)
14 x 26 13 1/4 x 11 1/2
(356 x 660) (337 x 292) (432 x 457)
Unit EPIC ECM Motor FLA
Size Motor HP 120V 208V 240V 277V
1 2.1 1.4
*
2 4.0 2.7
*
5.0 3.4
3
*
4 6.9 4.6
*
5 9.0 6.1
*
6 11.9 7.3
*
The ECM is a variable horsepower motor. Refer to
Selectworks schedule for actual power consumption.
Dimensions are in inches (mm).
B SERIES SUPERSEDES DRAWING NO.
3500 11 - 15 - 22
B
DW
W
W2
8"
PRIMARY
AIR
Filter Size
Top Inlet
(std.) (opt.)
10 x 12 14 x 16
(356 x 406)
10 x 12 14 x 16
(356 x 406)
14 x 16 16 x 16
(406 x 406)
16 x 16 16 x 25
(406 x 635)
16 x 16 16 x 25
(406 x 635)
17 x 18 18 x 28
(457 x 711)
1.3 1.2
2.6 2.6
3.3 3.3
4.5 4.2
5.8 5.6
7.3 7.2
35S-1