Crop - Panasonic HEVC Advance AW-UE160WP Operating Instructions Manual

Camera menu items (continued)
Camera Focus
Stores the value of focus position of this unit between 000555h
(NEAR) and 000FFFh (FAR).
Spare / User Defined (16bit)
Stores the value of iris position of this unit between 0555h (CLOSE)
and 0FFFh (OPEN).
Checksum
Stores the checksum value provided by the free-d protocol.
<NOTE>
• The camera control commands are not output from the RS-422
connector when [SERIAL] is [ON].
z IP output
• When [IP] of [TRACKING DATA OUTPUT] is set to [ON], the tracking
data for Pan/Tilt/Zoom or other information is synchronized with the
GENLOCK signal and outputs UDP packets via IP.
• Outputs simultaneously up to four clients (IP addresses) that have
been specified on the designated web screen (→ page 165).
• The tracking data is output in a format conforming to the free-d
protocol. The output specification (mode, command type, advanced
stored data) of this unit is equivalent to serial (RS-422) output.
<NOTE>
• When forwarding to more than one client, the timing of transmitting
the UDP packet to the second and subsequent client will always be
delayed relative to the GENLOCK signal.
(Approximately 200 to 300 μs delay will occur for each client. The
latency may be increased depending on the system status or the
network environment of the unit.)
• When [IP] is [ON], video transmission via IP may be delayed or the
video may suffer frame loss.
We recommend setting [IP] to [OFF] to avoid the delay or frame loss
due to the video transmission via IP.

CROP

UHD CROP [OFF, CROP(1080), CROP(720)]
Make overall CROP mode settings.
OFF No cropping.
CROP(1080) Cropped images output with 1080 resolution.
CROP(720) Cropped images output with 720 resolution.
<NOTE>
• Only when [2160/59.94p] or [2160/50p] is selected in
[BASIC CONFIG] – [FORMAT] are [OFF], [CROP(1080)], and
[CROP(720)] available for selection, and when [2160/60p],
[2160/29.97p], [2160/25p], [2160/24p], or [2160/23.98p] is selected,
[OFF] and [CROP(1080)] only may be selected.
When other selections are made in FORMAT, this will be [OFF].
CROP ZOOM [OFF, ON]
Make settings about whether to run cropping that uses D-ZOOM.
When [ON], you can set the ZOOM magnification.
(→ "CROP ZOOM RATIO")
This is only enabled when [UHD CROP] is set to [CROP(1080)] or
[CROP(720)].
CROP AF [OFF, ON]
Make settings about whether to run AF on images within the crop
frame.
This is only enabled when [UHD CROP] is set to [CROP(1080)] or
[CROP(720)].
3G SDI1 OUT [FULL, CROP]
Make the settings for FULL/CROP for images output to the 3G SDI
OUT connector.
FULL FHD down-converted images are output as is without
cropping UHD images.
CROP Images with FHD cropped from UHD images are output.
The images output in this case are those with the crop
frame specified in [CROP OUT].
This is only enabled when [UHD CROP] is set to [CROP(1080)] or
[CROP(720)].
NDI OUT [FULL, CROP]
Makes the settings for FULL/CROP for images output to High
bandwidth NDI transmission.
FULL FHD down-converted images are output as is without
cropping UHD images.
CROP Images with FHD cropped from UHD images are output.
The images output in this case are those with the crop
frame specified in [CROP OUT].
This is only enabled when [UHD CROP] is set to [CROP(1080)] or
[CROP(720)].
72