Table of Contents
Advertisement
Camera menu items (continued)
CY_B SAT [–127 to 0 to +126]
Adjust the color saturation. Set the color between cyan and blue.
CY_B PHASE [–127 to 0 to +126]
Adjust the hue. Set the color between cyan and blue.
B SAT [–127 to 0 to +126]
Adjust the color saturation. Set the color in the blue direction.
B PHASE [–127 to 0 to +126]
Adjust the hue. Set the color in the blue direction.
B_MG SAT [–127 to 0 to +126]
Adjust the color saturation. Set the color between blue and magenta.
B_MG PHASE [–127 to 0 to +126]
Adjust the hue. Set the color between blue and magenta.
MG_SAT [–127 to 0 to +126]
Adjust the color saturation. Set the color in the magenta direction.
MG_PHASE [–127 to 0 to +126]
Adjust the hue. Set the color in the magenta direction.
MG_R SAT [–127 to 0 to +126]
Adjust the color saturation. Set the color between magenta and red.
MG_R PHASE [–127 to 0 to +126]
Adjust the hue. Set the color between magenta and red.
R SAT [–127 to 0 to +126]
Adjust the color saturation. Set the color in the red direction.
R PHASE [–127 to 0 to +126]
Adjust the hue. Set the color in the red direction.
R_YE SAT [–127 to 0 to +126]
Adjust the color saturation. Set the color between red and yellow.
R_YE PHASE [–127 to 0 to +126]
Adjust the hue. Set the color between red and yellow.
YE SAT [–127 to 0 to +126]
Adjust the color saturation. Set the color in the yellow direction.
YE PHASE [–127 to 0 to +126]
Adjust the hue. Set the color in the yellow direction.
YE_G SAT [–127 to 0 to +126]
Adjust the color saturation. Set the color between yellow and green.
YE_G PHASE [–127 to 0 to +126]
Adjust the hue. Set the color between yellow and green.
DNR
Set the digital noise reduction level for outputting bright, clear images
without noise, even at night and low-light conditions. Noise can be
reduced by increasing the value.
However, image lag may increase.
<NOTE>
• For all of the DNR items, setting is not possible when [V-LOG] is
[ON] and [V-LOG PAINT SW] is [OFF].
DNR [OFF, ON]
Set ON/OFF for the digital noise reduction function.
DNR LEVEL [1 to 5]
Set the digital noise reduction level.
V‑LOG PAINT
Set the color temperature and noise reduction during V-LOG.
<NOTE>
• This is enabled only when [V-LOG PAINT SW] is [OFF].
COLOR TEMP SETTING
COLOR TEMP ACH/BCH
Set the color temperature and gain when the [WHITE BALANCE
MODE] is [AWB A] or [AWB B].
COLOR TEMP ACH [2000K to 15000K]
This displays the color temperature when [WHITE BALANCE
MODE] is [AWB A].
R GAIN ACH [–400 to +400]
This enables adjustments to R Gain when [WHITE BALANCE
MODE] is [AWB A].
B GAIN ACH [–400 to +400]
This enables adjustments to B Gain when [WHITE BALANCE
MODE] is [AWB A].
G AXIS ACH [–400 to +400]
Adjust the gain in the G-Mg direction when the [WHITE BALANCE
MODE] is [AWB A].
COLOR TEMP BCH [2000K to 15000K]
This displays the color temperature when [WHITE BALANCE
MODE] is [AWB B].
R GAIN BCH [–400 to +400]
This enables adjustments to R Gain when [WHITE BALANCE
MODE] is [AWB B].
B GAIN BCH [–400 to +400]
This enables adjustments to B Gain when [WHITE BALANCE
MODE] is [AWB B].
G AXIS BCH [–400 to +400]
Adjust the gain in the G-Mg direction when the [WHITE BALANCE
MODE] is [AWB B].
DNR
Set the digital noise reduction level for outputting bright, clear images
without noise, even at night and low-light conditions. Noise can be
reduced by increasing the value.
However, image lag may increase.
DNR [OFF, ON]
Set ON/OFF for the digital noise reduction function.
DNR LEVEL [1 to 5]
Set the digital noise reduction level.
67
Advertisement
Table of Contents
