Table of Contents
Advertisement
Parts and their functions (continued)
17.
AUDIO IN connector <AUDIO INPUT 1, 2>
Inputs external audio (microphone, line).
AUDIO INPUT 1, 2
1
GND
2
AUDIO IN (H)
2
1
3
3
AUDIO IN (C)
18.
3G SDI OUT connector <3G SDI OUT 1, 2/PM>
This is an SDI video signal output connector. Depending upon the
output signal format, 3G-SDI or 1.5G-SDI signals are output.
When using SMPTE ST2110, if images are input to SFP+, then the
images input as RETURN signals can be output as from 3G SDI
OUT2/PM.
<NOTE>
• A separate optional software key (AW-SFU60) needs to be
purchased to enable SMPTE ST2110 functionality.
19.
Ground connector
Connects to the ground connector on a wall outlet, ground bar, etc.
for grounding. (→ page 8)
20.
G/L IN connector <G/L IN>
This is the external sync signal input connector.
This unit supports BBS (Black Burst Sync) and tri-level
synchronization.
Supply to this connector the signals that correspond to the video
signal format which has been set.
Frequency: 119.88 Hz
External sync signal input format
Format
Tri‑level sync
1080/119.88p
―
Frequency: 100 Hz
External sync signal input format
Format
Tri‑level sync
1080/100p
―
Frequency: 60 Hz
External sync signal input format
Format
Tri‑level sync
2160/60p
1080/60p
1080/60p
Frequency: 59.94 Hz, 29.97 Hz
External sync signal input format
Format
Tri‑level sync
2160/59.94p
2160/29.97p
―
1080/59.94p
1080/29.97p
―
720/59.94p
BBS
1080/59.94i
480/59.94i
―
1080/29.97PsF
BBS
1080/50i
576/50i
―
1080/25PsF
BBS
―
―
―
BBS
1080/59.94i
480/59.94i
1080/29.97PsF
―
―
720/59.94p
Frequency: 50 Hz, 25 Hz
Format
2160/50p
2160/25p
―
1080/50p
1080/25p
―
720/50p
Frequency: 24 Hz
Format
2160/24p
1080/24p
1080/24p
Frequency: 23.98 Hz
Format
2160/23.98p
1080/23.98p
1080/23.98p
21.
RS‑422 connector <RS‑422>
This RS-422 connector (RJ-45) is connected when exercising serial
control over the unit from an external device. Use a cable with the
following specifications for the connection to this connector.
Furthermore, by shorting the R-TALLY signal (2-pin) with the GND
(1-pin), it is possible to light the tally lamp (red) in the camera head
section of the unit.
<NOTE>
• Do not connect PoE cable to the RS-422 port.
• Do not apply a voltage to the R_TALLY_IN signal pin.
• Menu settings enable the output to pin 7 and pin 8 of the red tally
and green tally signals received by the unit. Output is by contact
output, and normally is "OPEN", then it becomes "MAKE" for output.
(→ page 49, page 115)
• Control of this unit via the RS-422 connector (serial connection) is
not possible from Panasonic controllers (AW-RP150, AW-RP60).
To control this unit from Panasonic controllers (AW-RP150, AW-
RP60), control via the LAN connector (IP connection).
LAN cable
1
(category 5e or above, straight cable),
*
max. 1000 m (3280 ft)
1
Use of an STP (shielded twisted pair) cable is
*
recommended.
20
External sync signal input format
Tri‑level sync
1080/50i
576/50i
1080/25PsF
―
―
720/50p
External sync signal input format
Tri‑level sync
1080/24PsF
―
External sync signal input format
Tri‑level sync
1080/23.98PsF
―
Pin
Pin
Signal
No.
No.
1
GND
5
TXD+
2
R_TALLY_IN
6
RXD+
3
RXD–
7
OPTION_OUT1
4
TXD–
8
OPTION_OUT2
BBS
BBS
―
BBS
―
Signal
Advertisement
Table of Contents
