Schulte GLADIATOR RWP-1935 Operator's Manual

Variable width rock windrower/picker

Hide thumbs

Table Of Contents

100

Table of Contents

Quick Links

Download this manual

GLADIATOR RWP-1935

VARIABLE WIDTH ROCK WINDROWER/PICKER

Published 01/2023

This Operator's Manual is an integral part of the safe operation of this machine and

must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW

the Safety and Operation Instructions contained in this manual before operating the

equipment.

Schulte Industries Ltd.

PO Box 70

Englefeld Saskatchewan

Canada S0K 1N0

Tel. (306) 287-3715

Fax. (306) 287-3355

Parts Fax. (306) 287-4066

Web: www.schulte.ca

sn: R19020001211-R19020005301 inclusive

OPERATOR'S MANUAL

C01-Cover str

Part No. R190-010C

$0.00

Table of Contents

Summary of Contents for Schulte GLADIATOR RWP-1935

Page 1 GLADIATOR RWP-1935 VARIABLE WIDTH ROCK WINDROWER/PICKER Published 01/2023 sn: R19020001211-R19020005301 inclusive Part No. R190-010C OPERATOR’S MANUAL This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment.
Page 2 To the Owner/Operator/Dealer All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents.
Page 3 DEALER’S PREDELIVERY SERVICE GUIDE for the SCHULTE GLADIATOR RWP-1935 DETAILS OF ITEMS LISTED BELOW ARE COVERED IN THIS OPERATOR’S MANUAL ____ Shipping damage corrected ____ Set up machine as outlined in the shipping instructions attached to these instructions. ____ Check that all safety decals are in good condition, replace if necessary.
Page 5: Table Of Contents
Table of Contents SAFETY SECTION ..................1 - 1 GENERAL SAFETY INSTRUCTIONS AND PRACTICES................1 - 2 OPERATOR SAFETY INSTRUCTIONS AND PRACTICES ................1 - 3 EQUIPMENT OPERATION SAFETY INSTRUCTIONS AND PRACTICES ............ 1 - 5 CONNECTING OR DISCONNECTING IMPLEMENT SAFETY INSTRUCTIONS AND PRACTICES .... 1 - 8 TRANSPORTING SAFETY INSTRUCTIONS AND PRACTICES ..............
Page 6 Table of Contents STARTING THE TRACTOR ..........................4 - 8 CONNECTING THE ROCK PICKER TO THE TRACTOR ................4 - 9 Connecting the Rock Picker to the Tractor....................4 - 9 Safety Tow Chain ............................ 4 - 10 Connecting the PTO Pump to the Tractor ....................4 - 10 Connecting the Rock Picker Hydraulic Lines to the Tractor ..............
Page 7 Table of Contents NUTS AND BOLTS ............................5 - 5 Bolt Grades and Torque ..........................5 - 5 HYDRAULICS ..............................5 - 6 Hydraulic PTO Pump ..........................5 - 7 Hydraulic conditioning Unit (HCU) ........................5 - 8 Hydraulic Reservoir ........................... 5 - 8 Oil Cooler..............................
Page 10: General Safety Instructions And Practices
Safety Messages. Always use good common sense to avoid hazards. (SG-2) str Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad. (SG-3) str Gladiator RWP-1935 01/23 Safety Section 1-2 © 2023 Alamo Group Inc.
Page 11: Operator Safety Instructions And Practices
Never allow children to play on or around Tractor or Implement. Children can slip or fall off the Equipment and be killed or injured. Inadvertent contact with controls can cause the Implement to shift or fall crushing themselves or others. (SG-25) str Gladiator RWP-1935 01/23 Safety Section 1-3 © 2023 Alamo Group Inc.
Page 12 Contact with the rotating items can result in serious injury or even death. Stay clear until the implement is securely parked and all motion has stopped. (STL-12) str Gladiator RWP-1935 01/23 Safety Section 1-4 © 2023 Alamo Group Inc.
Page 13: Equipment Operation Safety Instructions And Practices
Operator’s Manuals, been trained in proper operation of the tractor and Implement, and are physically large enough to reach and operate the controls easily. (SG-11) str Gladiator RWP-1935 01/23 Safety Section 1-5 © 2023 Alamo Group Inc.
Page 14 Attacking insects can cause you to lose control of the tractor, which can result in serious injury or death to you or bystanders. Never dismount a moving tractor. (SG- 40) str Gladiator RWP-1935 01/23 Safety Section 1-6 © 2023 Alamo Group Inc.
Page 15 Hopper contents, which may exceed hundred pounds, could fall and crush a person resulting in possible injury or death. Use extrem care when handling or working on or in load hopper bin. (STL-22) str Gladiator RWP-1935 01/23 Safety Section 1-7 © 2023 Alamo Group Inc.
Page 16: Connecting Or Disconnecting Implement Safety Instructions And Practices
When operating in traffic always use the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you and watch out for the other guy. (SG-19)str Gladiator RWP-1935 01/23 Safety Section 1-8 © 2023 Alamo Group Inc.
Page 17: Maintenance And Service Safety Instructions And Practices
Never work under the Implement, the framework, or any lifted component unless the Implement is securely supported or blocked up to prevent sudden or inadvertent falling which could cause death or serious injury. (SG-14)str Gladiator RWP-1935 01/23 Safety Section 1-9 © 2023 Alamo Group Inc.
Page 18 Missing, broken, or worn items must be replaced at once to reduce the possibility of injury or death from thrown objects, entanglement, or blade contact. (SSM- 07str) Cancer and Reproductive Harm www.P65Warnings.ca.gov Gladiator RWP-1935 01/23 Safety Section 1-10 © 2023 Alamo Group Inc.
Page 19: Parts Safety Instructions And Practices
PARTS SAFETY INSTRUCTIONS AND PRACTICES PARTS INFORMATION Use of genuine Schulte replacement parts is your guarantee that parts are of the same quality and are manufactured to the same standards as the original equipment. These parts are made and tested to Schulte specifications.
Page 22 Park on Level Ground Max 10% Ground Slope 280-201 Canister, Manual R200-010C Operator’s Manual S000-110 REFLECT NOTE: 226-628 & 226-630 are not shown and are dependent upon where the Machine is Sold. Gladiator RWP-1935 01/23 Safety Section 1-14 © 2023 Alamo Group Inc.
Page 28 (Refer to U.S. Dept. of Labor, Employment Standard Administration, Wage & Home Division, Child Labor Bulletin #102.) Gladiator RWP-1935 01/23 Safety Section 1-20 © 2023 Alamo Group Inc.
Page 30 INTRODUCTION The Gladiator RWP-1935 is designed to windrow and pick small to medium surface rocks, roots and other debris from the fields. With proper maintenance as described in this manual, your Gladiator will provide years of dependable performance. It is required that all operators of this implement read this manual or be instructed of its contents as to safety, proper orientation and maintenance before beginning operation.
Page 31 NOTE: Warranties are honored only if completed “Owner Registration and Warranty” forms are received by Schulte within thirty days of delivery of the implement. 3. Record the Rock Windrower/Picker Model and Serial Numbers on the Warranty page at the front of the Operator’s Manual.
Page 32 GENERAL STATEMENT AFFECTING ALL SCHULTE WARRANTY Schulte Industries Ltd. warrants to the original purchaser only, that in the event of any defect in material or workmanship in the product sold by Schulte Industries, the subject of this warranty (“the goods”) during the warranty period mentioned below the manufacturer will provide the coverage specified below.
Page 33 • The Dealer must keep the failed part until the claim is processed, to allow Schulte Industries the option of further examination of the part. Further examination may mean that pictures are sent, or that the part be returned to Schulte.
Page 36: Before Operation
Match plate profile to ensure proper orientation. Mount the Walking Axle in the orientation shown (Axle Mount Sleeves up). Be sure to install retaining bolts in BOTH ends of the pin. Gladiator RWP-1935 01/23 Assembly Section 3-2 © 2023 Alamo Group Inc.
Page 37: Drum Sprocket
Nm). Over tightening will strip out bolts. Slide the appropriate amount of machine bushings until they are flush with end of shaft, then cap off and tighten end bolt. Gladiator RWP-1935 01/23 Assembly Section 3-3 © 2023 Alamo Group Inc.
Page 38: Drive Chain
Using the wrench provided with the machine, load the tensioner and secure with the Center Bolt. Gladiator RWP-1935 01/23 Assembly Section 3-4 © 2023 Alamo Group Inc.
Page 39: Drive Coupler
NOTE: Coupler misalignment of greater than 1 degree, or 0.015" will reduce the life of the coupler insert and may cause damage to other components of your rock picker. Gladiator RWP-1935 01/23 Assembly Section 3-5 © 2023 Alamo Group Inc.
Page 40: Pre-Delivery Customer Checklist
Are both Drum chains tightened? Is the Reel Motor coupler properly aligned? Are all teeth hard surfaced? Does implement operate smoothly at normal operating speed? Implement should not vibrate excessively. Gladiator RWP-1935 01/23 Assembly Section 3-6 © 2023 Alamo Group Inc.
Page 42 Pictures contained in this section are intended to be used as a visual aid to assist in explaining the operation of a Gladiator RWP-1935 Windrower and are not necessarily of a GLADIATOR RWP-1935 Windrower. Some pictures may show shields removed for picture clarity. NEVER OPERATE these implements without all shields in place and in good operational condition.
Page 43: Standard Equipment And Specifications
Flow control, variable 0-15 gpm (0-57) L/min Driven by PTO Pump (See Options Below) OPTIONS - PTO PUMPS 540 - 1-3/8” 6 Spline 1000 - 1-3/8” 21 Spline 1000 - 1-3/4” 20 Spline Gladiator RWP-1935 01/23 Operation Section 4-3 © 2023 Alamo Group Inc.
Page 44: Operator Requirements
Serious injury or death to the operator or others could result if the operator is under the influence of drugs or alcohol. (SG- 27) str Gladiator RWP-1935 01/23 Operation Section 4-4 © 2023 Alamo Group Inc.
Page 45: Tractor Requirements
The recommended tractor HP for the GLADIATOR RWP-1935 is 125 HP (93 kW). Operating the implement with to large of a tractor will greatly increase the risk of damaging the implement...
Page 46: Drawbar
Serious bodily injury and/ or equipment failure can result from using a PTO adapter. Consult an authorized dealer for assistance if the Implement driveline does not match the Tractor PTO. (S3PT-14) str Gladiator RWP-1935 01/23 Operation Section 4-6 © 2023 Alamo Group Inc.
Page 47: Tire Spacing
Never allow passengers to ride on the tractor or attached equipment. Riders can easily fall off and be seriously injured or killed from falling off and being ran over. It is the operator’s responsibility to forbid all extra riders at all times. OPS-U- 0008str Gladiator RWP-1935 01/23 Operation Section 4-7 © 2023 Alamo Group Inc.
Page 48: Dismounting The Tractor
• The 3-point hitch control lever is in the lowered position. • The hydraulic remote control levers are in the neutral position. • The tractor transmission levers are in park or neutral. Gladiator RWP-1935 01/23 Operation Section 4-8 © 2023 Alamo Group Inc.
Page 49: Connecting The Rock Picker To The Tractor
Place a block in front of and behind wheels to prevent the GLADIATOR RWP-1935 from moving. Keep hands and feet out from under the GLADIATOR RWP-1935 and clear of pinch points between the tractor and GLADIATOR RWP-1935.
Page 50: Safety Tow Chain
Tractor PTO shaft, Align the pump splines with the tractor PTO splines. Compress the lock collar spring and slide the pump into place. Release the spring and ensure the pump is locked in place. Gladiator RWP-1935 01/23 Operation Section 4-10 © 2023 Alamo Group Inc.
Page 51 When turning the tractor with the implement attached, be careful that no part of the tractor comes in contact with the hydraulic cooler. This could damage the implement or tractor. A punctured cooler could create a hazard causing injury or death. Gladiator RWP-1935 01/23 Operation Section 4-11 © 2023 Alamo Group Inc.
Page 52: Connecting The Rock Picker Hydraulic Lines To The Tractor
Keep implement hydraulic lines, hoses, quick couplers, and swivels free of contamination. Never leave a disconnected hose end open and cap the tractor hydraulic outlet ports when not in use. If the tractor ports, GLADIATOR RWP-1935 ports hydraulic hose...
Page 53: Connecting The Electronic Controls To The Tractor
Ensure that no one is near the machine while hydraulics are being activated. 1. First find a level area and unfold the machine. 2. Lower the frame until the Grate Teeth just touch the ground. Gladiator RWP-1935 01/23 Operation Section 4-13 © 2023 Alamo Group Inc.
Page 54 Lower the drum by raising the wheel. NOTE: When adjusting the gauge wheel level be sure to store the ratchet jack handle in a position where it won’t interfere with the machine function. Gladiator RWP-1935 01/23 Operation Section 4-14 © 2023 Alamo Group Inc.
Page 55: Adjusting Machine Width
During normal operation small amounts of oil may leak past piston seals causing cylinders to fall out of synchronization. Synchronization can be restored by fully extending cylinders and holding the circuit open for period of time Gladiator RWP-1935 01/23 Operation Section 4-15 © 2023 Alamo Group Inc.
Page 56: Pre-Operation Inspection And Service
Implement. Never work on the Implement with the tractor PTO attachment connected and running. Rotating parts, drums, teeth, chains, or drives could turn without warning and cause immediate entanglement, injury or death. (S3PT-24)str Gladiator RWP-1935 01/23 Operation Section 4-16 © 2023 Alamo Group Inc.
Page 57: Tractor Pre-Operation Inspection/Service
Ensure the manual canister is secured to the equipment with the operator’s manual inside. • Ensure all safety signs are in place and legi- ble. Replace missing, damaged, and illegible decals. OPS-U- 0011 str Gladiator RWP-1935 01/23 Operation Section 4-17 © 2023 Alamo Group Inc.
Page 58 • Inspect the condition of the wing drive chains. Ops-3085 • Ensure the chain tensioner are properly set. • Ensure chain case shields are secure and in good condition. Gladiator RWP-1935 01/23 Operation Section 4-18 © 2023 Alamo Group Inc.
Page 59 PTO and the locking collar is seated in the groove of the PTO shaft. • Ensure the PTO pump chain is securely fastened to the tractor so the pump cannot rotate. OPS-RP-0014 str Gladiator RWP-1935 01/23 Operation Section 4-19 © 2023 Alamo Group Inc.
Page 60 IMPORTANT: DO NOT use your hands to check for oil leaks. Use a piece of heavy paper or cardboard to check for hydrau- lic oil leaks. OPS-RP-0004_E str Gladiator RWP-1935 01/23 Operation Section 4-20 © 2023 Alamo Group Inc.
Page 61 Inspect rock pickers tire condition, wheel bearings, and lug nut torque. • Ensure tire pressure is to suggested specifica- tions. Refer to maintenance sections of your operators manual. OPS-RP-0005_D str Gladiator RWP-1935 01/23 Operation Section 4-21 © 2023 Alamo Group Inc.
Page 62 Transport locks are in good condition and operational Proper hourly greasing done as per Operator’s Manual _______________________________ __________________________________ Make: Shift: ____________________________________________ Operator’s Signature: DO NOT OPERATE an UNSAFE TRACTOR or IMPLEMENT Gladiator RWP-1935 01/23 Operation Section 4-22 © 2023 Alamo Group Inc.
Page 63 The radiator is free of debris The air filter is in good condition Proper hourly greasing is done per Operator’s Manual ____________________________________________ Operator’s Signature: DO NOT OPERATE an UNSAFE TRACTOR or IMPLEMENT Gladiator RWP-1935 01/23 Operation Section 4-23 © 2023 Alamo Group Inc.
Page 64: Driving The Tractor And Rock Picker
Such an impact could cause the Implement and Tractor to pivot violently resulting in loss of steering control, death, or serious injury. Never allow the Implement to contact obstacles. (S3PT-12)str Gladiator RWP-1935 01/23 Operation Section 4-24 © 2023 Alamo Group Inc.
Page 65: Starting The Tractor
4. Inspect the pump speed, pressure lines for leaks, check oil level in the sight gauge and add more oil until it reaches the top portion of the sight gauge. 5. Let the system run for a couple of minutes to make sure the HCU is running smoothly. Gladiator RWP-1935 01/23 Operation Section 4-25 © 2023 Alamo Group Inc.
Page 66: Operating The Wings
Allow ample clearance around the implement when folding or unfolding the wings. Use extreme caution around buildings or overhead power lines. (S3PT-05) str Gladiator RWP-1935 01/23 Operation Section 4-26 © 2023 Alamo Group Inc.
Page 67: Driving The Tractor And Rock Picker
Raising the implement exposes the drum teeth which creates a potentially serious hazard and could cause serious injury or even death from objects thrown from the drum teeth. Gladiator RWP-1935 01/23 Operation Section 4-27 © 2023 Alamo Group Inc.
Page 68: Crossing Ditches And Steep Inclines
Damage resulting from over-collapse of the driveline’s inner profile and its outer housing may allow the driveline to come loose from the Tractor which could cause bodily injury to the operator or bystanders and/or extensive damage to the Tractor or Implement Gladiator RWP-1935 01/23 Operation Section 4-28 © 2023 Alamo Group Inc.
Page 69: Operating The Tractor And Implement
Inspect the area for such objects before working in the area. Remove any such objects from the site. Never allow the implement to contact such objects. (STL-6_A) str Gladiator RWP-1935 01/23 Operation Section 4-29 © 2023 Alamo Group Inc.
Page 70: Foreign Debris Hazards
Make sure the PTO shield, integral driveline shields, and input shields are installed when using PTO-driven equipment. Always replace any shield if it is damaged or missing. (S3PT-8) str Gladiator RWP-1935 01/23 Operation Section 4-30 © 2023 Alamo Group Inc.
Page 71: Ground Speed
REMOVE the HOSE and have it tested at a Dealer. If oil does penetrate the skin, have the injury treated immediately by a physician knowledgeable and skilled in this procedure. (SG-15) str Gladiator RWP-1935 01/23 Operation Section 4-31 © 2023 Alamo Group Inc.
Page 72 The Gladiator RWP-1935 Rock Picker is designed primarily for picking surface rock. Do not use the machine to dig out buried rock. Bring large rocks to the surface first, then pick them. If a rock is too large to immediately be swept into the bucket, raising the grate slightly will help in loading the rock.
Page 73 Stay alert and watch for trees, power lines, posts, signs, and all other overhead and ground obstructions while you are rock picking. Use extreme care to avoid hitting these types of obstructions. Gladiator RWP-1935 01/23 Operation Section 4-33 © 2023 Alamo Group Inc.
Page 74: Shutting Down The Implement
3. Once the unit tongue is being supported entirely by the jack, remove the hitch pin, and lynch pin. Gladiator RWP-1935 01/23 Operation Section 4-34 © 2023 Alamo Group Inc.
Page 75: Rock Picker Storage
Keep the hydraulic lines from sitting in water, dirt and other contaminants. • Use spray touch-up enamel where necessary to prevent rust and maintain the appearance of the imple- ment. OPS-RP-0006 str Gladiator RWP-1935 01/23 Operation Section 4-35 © 2023 Alamo Group Inc.
Page 76 Implement from the Tractor 3-point hitch. Always shut the Tractor off completely and set the parking brake before attempting to disconnect the Implement pins from the Tractor hitch. Gladiator RWP-1935 01/23 Operation Section 4-36 © 2023 Alamo Group Inc.
Page 77: Transporting The Tractor And Implement
20 MPH (32 kph). OPS-U- 0018 str In wet conditions where there is a likelihood of material collecting on the Implement, make certain that this material is removed before traveling on public roadways. (STL-7) str Gladiator RWP-1935 01/23 Operation Section 4-37 © 2023 Alamo Group Inc.
Page 78: Transporting On Public Roadways
Replace the SMV emblem if faded, damaged, or no longer reflective Gladiator RWP-1935 01/23 Operation Section 4-38 © 2023 Alamo Group Inc.
Page 79 Such an impact could cause the Implement and Tractor to pivot violently resulting in loss of steering control, death, or serious injury. Never allow the Implement to contact obstacles. (S3PT-12)str Gladiator RWP-1935 01/23 Operation Section 4-39 © 2023 Alamo Group Inc.
Page 80 When operating in traffic always use the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you and watch out for the other guy. (SG-19)str Gladiator RWP-1935 01/23 Operation Section 4-40 © 2023 Alamo Group Inc.
Page 81: Hauling The Tractor And Implement
If during transport a hard braking, sharp turning, or swerving action was performed, stop at the next safe location to inspect the security of the load. OPS-U- 0026str Gladiator RWP-1935 01/23 Operation Section 4-41 © 2023 Alamo Group Inc.
Page 82: Troubleshooting Guide
Hydraulic System Hydraulic Cylinders not Oil not getting to Cylinders Check Hydraulic connections functioning Check Valve Block and Solenoids Electronic Switch Box not functioning Check Electrical connections Gladiator RWP-1935 01/23 Operation Section 4-42 © 2023 Alamo Group Inc.
Page 84: Drive Coupler
NOTE: Experience has shown that the majority of breakdowns are the result of inadequate or improper service and inspection. The Gladiator RWP-1935 is equipped with a zero maintenance direct-drive Magnaloy Hytrel Coupler system which is designed to provide years of heavy duty service.
Page 85: Reel Hydraulic Motor
REEL HYDRAULIC MOTOR The Gladiator RWP-1935 is equipped with a Heavy Duty Hydraulic Motor with a built in cushion valve for shock protection and long motor life. The motor also contains a case drain port that is integral in extending the life of the motor components.
Page 86 21. Install nine assembly bolts (22) into endcover and pre-torque to 13,6 Nm [10 ft. lb.]. Final torque all bolts to 69,8 ± 7,5 Nm [51.5 ± 5.5 ft. lb.]. NOTE: See Parts Manual for corresponding part numbers Gladiator RWP-1935 01/23 Maintenance Section 5-4 © 2023 Alamo Group Inc.
Page 87: Nuts And Bolts
[Refer to the “Parts” section]. Do not replace lock nuts with nuts and lock washers. Use only original equipment lock nuts. Recommended Torques in foot pounds for SAE Grade 5 bolts, based on dry assembly: Gladiator RWP-1935 01/23 Maintenance Section 5-5 © 2023 Alamo Group Inc.
Page 88: Hydraulics
Relieve hydraulic pressure before performing maintenance or repairs. Use gloves and eye protection when servicing hot components. Contact with a hot surface or fluid can cause serious injury from burns or scalding. (SG-34str) Gladiator RWP-1935 01/23 Maintenance Section 5-6 © 2023 Alamo Group Inc.
Page 89: Hydraulic Pto Pump
1.1 L of oil (1.16 qt.) Gearbox should meet following specifications: -API Service Classifications GL-5 -Military Specification MIL-L-2105C Consult chart viscosity recommendations. NOTE: Use SAE 80-90 Gear Oil Gladiator RWP-1935 01/23 Maintenance Section 5-7 © 2023 Alamo Group Inc.
Page 90: Hydraulic Conditioning Unit (Hcu)
200F. the filter also comes with a bypass and it is rated for 25 psi. Do not open the internal bypass valve assembly port. Warranty is void if it has been opened, tampered, or damaged by the customer. Gladiator RWP-1935 01/23 Maintenance Section 5-8 © 2023 Alamo Group Inc.
Page 91: Oil Cooler
System pressure on this manifold is set to 2500 psi and the flow control pressure compensated valve bleeds the flow to the hydraulic fan drive motor. The flow control pressure compensated valve is set to 2 gpm for the hydraulic motor to run the fan. Gladiator RWP-1935 01/23 Maintenance Section 5-9 © 2023 Alamo Group Inc.
Page 92: Filter/Breather Replacement
• Check for potential cracks in the mounting brackets. • Inspect high pressure hose lines for bends, wear and tear. Every 9 Months • All of the 3 month Maintenance items • Replace filter and breather Gladiator RWP-1935 01/23 Maintenance Section 5-10 © 2023 Alamo Group Inc.
Page 93: How To Drain The Hcu
How to Clean the Oil Cooler Schulte recommends pressurized water or compressed air to be sprayed parallel to the direction of the fins to clean the external dust and debris. The pressurized water or compressed air spray should be placed on the opposite side of the air flow to remove air borne contaminants.
Page 94: Tightening Instructions For 812 Hubs
There should not be any drag noticed when spinning a tire installed on a hub. If the axle nut is too tight, the rollers of the wheel bearings will remove the grease from the bearing races, decreasing the life of the bearings. Gladiator RWP-1935 01/23 Maintenance Section 5-12 © 2023 Alamo Group Inc.
Page 95: Tires And Wheels
Hard surfacing applied to the windrower teeth should be reapplied before the original hard surface material has been worn off. Once the hard surface material is gone wear to the base metal of the teeth will be very rapid. CX170 hard surfacing electrodes are recommended.. Gladiator RWP-1935 01/23 Maintenance Section 5-13 © 2023 Alamo Group Inc.
Page 96: Lubrication
Grease points around the Rock Picker will be identified by one of the following greasing decals. In some cases, multiple grease points may be identified by a single decal if they are close together and the require the same greasing schedule. Gladiator RWP-1935 01/23 Maintenance Section 5-14 © 2023 Alamo Group Inc.
Page 97: Drive Chain
Check that all transport locks are in good condition and, if removed, reinstall all locks before moving the machine. Gladiator RWP-1935 01/23 Maintenance Section 5-15 © 2023 Alamo Group Inc.
Page 100 Gladiator RWP-1935 01/23 P/N R190-010C Printed Canada...

Schulte GLADIATOR RWP-1935 Operator's Manual

Quick Links

Related Manuals for Schulte GLADIATOR RWP-1935

Summary of Contents for Schulte GLADIATOR RWP-1935

Table of Contents