Schulte SMR-600 Operator's Manual

Multi-rake

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Published 04/21

This Operator's Manual is an integral part of the safe operation of this

machine and must be maintained with the unit at all times. READ,

UNDERSTAND, and FOLLOW the Safety and Operation Instructions

contained in this manual before operating the equipment. C01-Cover

Schulte Industries Ltd.

PO Box 70

Englefeld Saskatchewan

Canada S0K 1N0

Tel. (306) 287-3715

Fax. (306) 287-3355

Parts Fax. (306) 287-4066

Web: www.schulte.ca

SMR-600

MULTI-RAKE

OPERATOR'S MANUAL

Part No. R700-010C

Table of Contents

Summary of Contents for Schulte SMR-600

Page 1 READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. C01-Cover Schulte Industries Ltd. PO Box 70 Englefeld Saskatchewan Canada S0K 1N0 Tel.
Page 2 PRIME MOVER To the Owner/Operator/Dealer All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents.
Page 3 DEALER’S PREDELIVERY SERVICE GUIDE for the SCHULTE SMR-600 DETAILS OF ITEMS LISTED BELOW ARE COVERED IN THIS OPERATOR’S MANUAL ____Shipping damage corrected ____Set up machine as outlined in the shipping instructions attached to these instructions. ____Check that all safety decals are in good condition, replace if necessary.
Page 5: Table Of Contents
Dismounting the Skid Steer ..........................4-6 STARTING THE SKID STEER ...........................4-7 CONNECTING THE SMR-600 TO THE SKID STEER ..................4-8 Connecting the SMR-600 to the Skid Steer Mount ....................4-8 Connecting the Multi Rake Windrower and Skid Steer Hydraulic Lines .............4-9 PRE-OPERATION INSPECTION AND SERVICE .....................4-9...
Page 6 Windrower Pre-Operation Inspection/Service ....................4-10 ROADSIDE OPERATION ..........................4-12 DRIVING THE SKID STEER AND MULTI RAKE WINDROWER ..............4-15 Starting the Skid Steer .............................4-16 OPERATING THE SKID STEER AND MULTI RAKE WINDROWER ..............4-16 Foreign Debris Hazards ...........................4-17 Ground Speed ..............................4-17 Engaging the Windrower From the Skid Steer ....................4-18 Drum Speed ..............................4-18 OPERATING THE WINDROWER ........................4-18 Shutting Down the Implement ..........................4-20...
Page 8: General Safety Instructions And Practices
Safety Messages. Always use good common sense to avoid hazards. (SG-2) Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad. (SG-3) SMR-600 04/21 SMR-600 04/21 Safety Section 1-2 Safety Section 1-2 © 2019 Alamo Group Inc.
Page 9: Operator Safety Instructions And Practices
The operator and all support personnel should wear hard hats, safety shoes, safety glasses, and proper hearing protection at all times for protection from injury including injury from items that may be thrown by the equipment. (SG-16) SMR-600 04/21 Safety Section 1-3 © 2019 Alamo Group Inc.
Page 10 Never allow children to play on or around Power Unit or Implement. Children can slip or fall off the Equipment and be injured or killed. Inadvertent contact with controls can cause the implement to shift or fall crushing themselves or others. SMR-600 04/21 SMR-600 04/21 Safety Section 1-4 Safety Section 1-4 ©...
Page 11 Contact with the rotating items can result in serious injury or even death. Stay clear until the implement is securely parked and all motion has stopped. (STL-12) SMR-600 04/21 Safety Section 1-5 © 2019 Alamo Group Inc.
Page 12: Equipment Operation Safety Instructions And Practices
Never dismount a Power Unit that is moving or while the engine is running. Operate the power unit controls from the power unit seat only. SMR-600 04/21 SMR-600 04/21 Safety Section 1-6 Safety Section 1-6...
Page 13 Do not exceed the rated speed for the Implement. Excessive speeds can cause Implement motor, chain, or drum failures resulting in serious injury or death. SMR-600 04/21 Safety Section 1-7 © 2019 Alamo Group Inc.
Page 14 This Implement is capable of throwing objects for significant distances and causing serious injury. Stop the Power Unit and Implement immediately if a bystander or animal comes near the equipment. SMR-600 04/21 SMR-600 04/21 Safety Section 1-8 Safety Section 1-8...
Page 15: Connecting Or Disconnecting Implement Instructions And Practices
Make certain that the “Slow Moving Vehicle” (SMV) sign is installed in such a way as to be clearly visible and legible. When transporting the Equipment use the Tractor flashing warning lights and follow all local traffic regulations. (SG-6) SMR-600 04/21 Safety Section 1-9 © 2019 Alamo Group Inc.
Page 16 Implement by at least 20%. Never tow the Implement and another Implement connected in tandem. Never tow the Implement at speeds over 20 MPH. SMR-600 04/21 SMR-600 04/21 Safety Section 1-10 Safety Section 1-10...
Page 17: Maintenance And Service Safety Instructions And Practices
Make sure all pins have cotter pins and washers. Serious injury may occur from not maintaining this machine in good working order. (SG-21) SMR-600 04/21 Safety Section 1-11 © 2019 Alamo Group Inc.
Page 18: Cancer And Reproductive Harm Www.p65Warnings.ca.gov
Missing, broken, or worn items must be replaced at once to reduce the possibility of injury or death from thrown objects, entanglement, or contact. (SSM-07) Cancer and Reproductive Harm www.P65Warnings.ca.gov. SMR-600 04/21 SMR-600 04/21 Safety Section 1-12 Safety Section 1-12...
Page 19: Concluding Safety Instructions And Practices
PARTS SAFETY INSTRUCTIONS AND PRACTICES PARTS INFORMATION Use of genuine Schulte replacement parts is your guarantee that parts are of the same quality and are manufactured to the same standards as the original equipment. These parts are made and tested to Schulte specifications.
Page 20: Decal Location
SAFETY Decal Location SMR-600 04/21 SMR-600 04/21 Safety Section 1-14 Safety Section 1-14 © 2019 Alamo Group Inc.
Page 21 LEVEL DESCRIPTION 213-001 -------------- Safety Walk Tape, 9” 226-004 LOGO FEMA Member 226-100 SER PLT Serial Plate 226-116 LOGO Schulte Logo, Small Profile 226-144 DANGER Moving Parts Hazard 226-151 DANGER Throw Rock 226-1531 REFLECTOR Red Reflector 226-1541 REFLECTOR Amber Reflector...
Page 22: Decal Description
SAFETY Decal Description SMR-600 04/21 SMR-600 04/21 Safety Section 1-16 Safety Section 1-16 © 2019 Alamo Group Inc.
Page 28 INTRODUCTION The SMR-600 is the perfect tool for your Skid Steer with its ability for Windrowing, Landscaping, Soil Conditioning and Sweeping. The SMR-600 Multi Rake Windrower roto- tilling action breaks lumps, roots and other debris while reclaiming rocks by forming them in uniform row.
Page 29: Equipment & Specifications
NOTE: Warranties are honored only if completed “Owner Registration and Warranty” forms are received by Schulte within thirty days of delivery of the implement. 3. Record the Windrower Model and Serial Numbers on the Warranty page at the front of the Operator’s Manual.
Page 30 GENERAL STATEMENT AFFECTING ALL SCHULTE WARRANTY Schulte Industries Ltd. warrants to the original purchaser only, that in the event of any defect in material or workmanship in the product sold by Schulte Industries, the subject of this warranty (“the goods”) during the warranty period mentioned below the manufacturer will provide the coverage specified below.
Page 31 • The Dealer must keep the failed part until the claim is processed, to allow Schulte Industries the option of further examination of the part. Further examination may mean that pictures are sent, or that the part be returned to Schulte.
Page 34: Before Operation
Check tire inflation pressure. Tires should be inflated to 45 PSI. Higher pressures may cause excessive bouncing over rough ground. SMR-600 04/21 Assembly Section 3-2 © 2019 Alamo Group Inc.
Page 35: Drum Sprocket
Check that the tension is set properly by ensuring the spring washers are flush with the top of the spacers as shown. • Ensure the jam nuts are fully locked to prevent backing off. SMR-600 04/21 Assembly Section 3-3 © 2019 Alamo Group Inc.
Page 36: Skid Steer Mounting
READ THE ‘OPERATION’ SECTION OF YOUR SKID STEER OPERATOR’S MANUAL BEFORE ATTEMPTING TO OPERATE THE SKID STEER AND SMR-800. 1. Check with your local Schulte dealer or the factory to ensure that you have the correct size hydraulic motor for your make and model of skid steer.
Page 37: Joystick Control Harness (Option)
6. Route the 6-pin plug end up through the tube of the loader arm to the front of the skid steer. The 6-pin plug can be secured in the most convenient location, such as with the hydraulic connections. SMR-600 04/21 Assembly Section 3-5...
Page 38: Electric Harness Kit
2. Route the 6-pin plug end of the harness up through the cut-out in the shield. Connect the plug end to the plug end on the skid steer. 3. Secure harness to the main hydraulic hoses with cable ties. SMR-600 04/21 Assembly Section 3-6 © 2019 Alamo Group Inc.
Page 39: Pre-Delivery Customer Checklist
 Is drum rotation correct?  Does implement operate smoothly at normal operating speed? Implement should not vibrate excessively.  Is the chain properly tensioned with washers flush with spacers? SMR-600 04/21 Assembly Section 3-7 © 2019 Alamo Group Inc.
Page 42 SMR-600, power unit, or a thrown object. Do not operate the SMR-600 if passersby, pets, livestock, or property are within 100 feet of the unit.
Page 43: Operator Requirements
NEVER knowingly allow anyone to operate this equipment when their alertness or coordination is impaired. Serious injury or death to the operator or others could result if the operator is under the influence of drugs or alcohol. (SG-27_A) SMR-600 04/21 Operation Section 4-3 © 2019 Alamo Group Inc.
Page 44: Skid Steer Requirements
This machine is equipped with a generic mounting system that will fit most makes and models of skid steer loaders. When mounting, ensure the locking pins fully engage the bottom holes in the mount in order to prevent accidental disconnection resulting in machine damage, injury, or possible death. SMR-600 04/21 Operation Section 4-4 © 2019 Alamo Group Inc.
Page 45: Motor
SMR-600. Refer to the SMR-600 Parts Manual for skid steer motor mount. 2.6 Auxiliary Hydraulics The skid steer must be equipped with Front Auxiliary Hydraulics.
Page 46: Getting On And Off The Skid Steer
Never dismount a Power Unit that is moving or while the engine is running. Operate the Power Unit controls from the operator seat only. (SPU-15) SMR-600 04/21 Operation Section 4-6 © 2019 Alamo Group Inc.
Page 47: Starting The Skid Steer
Start the Power Unit only when properly seated in the Power Unit seat. Starting a Power Unit in gear can result in injury or death. Read the Power Unit Operator’s Manual for proper starting instructions. (SPU-19) SMR-600 04/21 Operation Section 4-7 © 2019 Alamo Group Inc.
Page 48: Connecting The Smr-600 To The Skid Steer
Implement to the Skid Steer. (S3PT-15_A) 5.1 Connecting the SMR-600 to the Skid Steer Mount 1. Follow the instructions with your skid steer loader to quick attach the SMR-800 to the skid steer loader.
Page 49: Connecting The Multi Rake Windrower And Skid Steer Hydraulic Lines
4. The SMR-600 will operate with oil fed in either direction. If the drum turns in the opposite direction than desired, try engaging the auxiliary hydraulic flow in the opposite direction.
Page 50: Skid Steer Pre-Operation Inspection/Service
The teeth are made from high strength abrasion resistant 450BHN steel which provides superior wear resistance. However, under certain operating conditions, some wear is to be expected. • Hydraulic motor is in good condition and free of damage. SMR-600 04/21 Operation Section 4-10 © 2019 Alamo Group Inc.
Page 51 IMPORTANT: DO NOT use your hands to check for oil leaks. Use a piece of heavy paper or cardboard to check for hydraulic oil leaks. OPS-W-0010 SMR-600 04/21 Operation Section 4-11 © 2019 Alamo Group Inc.
Page 52: Roadside Operation
Increase the drum speed by replacing the hydraulic motor option with a smaller motor. Consult your nearest Schulte dealer for further information. The windrower should never be operated on the center (crown) of the road as this will cause excessive wear of the teeth near the center of the drum.
Page 53 The air filter is in good condition Park brake is in working order The brake fluid level is full Back-up alarm works if applicable Operator’s Signature: DO NOT OPERATE an UNSAFE SKID STEER or IMPLEMENT SMR-600 04/21 Operation Section 4-13 © 2019 Alamo Group Inc.
Page 54 Transport locks are in good condition All safety guards are installed and in good condition Machine is properly greased as per Operator’s Manual Operator’s Signature: DO NOT OPERATE an UNSAFE SKID STEER or IMPLEMENT SMR-600 04/21 Operation Section 4-14 © 2019 Alamo Group Inc.
Page 55: Driving The Skid Steer And Multi Rake Windrower
When operating in traffic always use the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you and watch out for the other guy. (SG-19) SMR-600 04/21 Operation Section 4-15 © 2019 Alamo Group Inc.
Page 56: Starting The Skid Steer
Inspect the area for such objects before working in the area. Remove any such objects from the site. Never allow the implement to contact such objects. (STL-6_A) SMR-600 04/21 Operation Section 4-16 © 2019 Alamo Group Inc.
Page 57: Foreign Debris Hazards
As the severity of ground conditions increase, the ground speed should decrease while maintaining drum speed. This will also help to prevent the drum from stalling under heavy workloads. SMR-600 04/21 Operation Section 4-17 © 2019 Alamo Group Inc.
Page 58: Engaging The Windrower From The Skid Steer
For the machine to operate effectively, the drum must rotate opposite of the direction of travel. For example, when traveling forward, the ground engaging teeth must push material forward. When traveling in reverse, the ground engaging teeth must drag material with you. SMR-600 04/21 Operation Section 4-18 © 2019 Alamo Group Inc.
Page 59 Stay alert and watch for trees, powerlines, posts, signs, and all other overhead ground obstructions while you are windrowing. Use extreme care to avoid hitting these types of obstructions. SMR-600 04/21 Operation Section 4-19 © 2019 Alamo Group Inc.
Page 60: Shutting Down The Implement
5. Board the skid steer, fasten your seatbelt, and start the engine. Tilt the mounting plate forward and back away from the windrower at the same time. The windrower should be released from the skid steer at this point. SMR-600 04/21 Operation Section 4-20 © 2019 Alamo Group Inc.
Page 61: Windrower Storage
Never allow children to play on or around Tractor or Implement. Children can slip or fall off the Equipment and be injured or killed. Inadvertent contact with controls can cause the Implement to shift or fall crushing themselves or others. (SG-25) SMR-600 04/21 Operation Section 4-21 © 2019 Alamo Group Inc.
Page 62: Transporting The Skid Steer And Windrower
Make certain that the “Slow Moving Vehicle” (SMV) sign is installed in such a way as to be clearly visible and legible. When transporting the Equipment use the Power Unit flashing warning lights and follow all local traffic regulations. (SPU-13) SMR-600 04/21 Operation Section 4-22 © 2019 Alamo Group Inc.
Page 63: Hauling The Skid Steer And Windrower
If during transport a hard braking, sharp turning, or swerving action was performed, stop at the next safe location to inspect the security of the load. SMR-600 04/21 Operation Section 4-23 © 2019 Alamo Group Inc.
Page 64: Troubleshooting Guide
Drum is obstructed Shut off skid steer engine and remove obstruction. Obstruction of sprocket key Replace sprocket key. Failure of hydraulic motor Repair or replace motor. SMR-600 04/21 Operation Section 4-24 © 2019 Alamo Group Inc.
Page 65 Auxiliary hydraulics not engaged Engage auxiliary hydraulics. Drum must be turning in order to cycle the angling cylinder. Electrical failure Refer to skid steer operators manual for how to check auxiliary electrical circuits. SMR-600 04/21 Operation Section 4-25 © 2019 Alamo Group Inc.
Page 68 MAINTENANCE PARTS INFORMATION Use of genuine Schulte replacement parts is your guarantee that parts are of the same quality and are manufactured to the same standards as the original equipment. These parts are made and tested to Schulte specifications. Non-genuine "will fit" parts do not consistently meet these specifications. The use of "will fit"...
Page 69: Nuts And Bolts
[Refer to the “Parts” section]. Do not replace lock nuts with nuts and lock washers. Use only original equipment lock nuts. Recommended Torques in foot pounds for SAE Grade 5 bolts, based on dry assembly: SMR-600 04/21 Maintenance Section 5-3 © 2019 Alamo Group Inc.
Page 70: Drive Chain
If any damage, or leaks are found repair or replace as needed. • If chain case contamination has occurred, clean chain case and replace oil with 0.7 liters (1.5 pints) of 80W90 gear oil. SMR-600 04/21 Maintenance Section 5-4 © 2019 Alamo Group Inc.
Page 71: Windrower Teeth
If the power unit ports or windrower hydraulic hose ends become contaminated, wipe clean with a rag before connecting. SMR-600 04/21 Maintenance Section 5-5 © 2019 Alamo Group Inc.
Page 72: Lubrication - Grease Schedule
Pivot drum until the cylinder is retracted. Ensure cylinder is full of oil. If cylinder is not full of oil, hydraulic cylinders and lines are filled by holding the valve control levers in the extended position until the cylinder fully SMR-600 04/21 Maintenance Section 5-6...
Page 73: Ramlok Disassembly Procedure
(see steps #3, 4 and 5). Again, note the rotation used to remove the wire and use the opposite rotation for assembly. There is only one wire hole in the butt. SMR-600 04/21 Maintenance Section 5-7 © 2019 Alamo Group Inc.
Page 74 14. Replace all damaged components. It is recommended that all seals be replaced, even if there is no visible damage. 15. Assembly is the opposite of disassembly. Use a small amount of oil to lubricate all seals prior to assembly. Caution must be used to prevent seal damage. SMR-600 04/21 Maintenance Section 5-8 © 2019 Alamo Group Inc.
Page 76 SMR-600 - 04/21 P/N R700-010C Printed Canada...

Schulte SMR-600 Operator's Manual

Quick Links

Related Manuals for Schulte SMR-600

Summary of Contents for Schulte SMR-600

Table of Contents