General Description; Hardware Specifications; Electronics Specifications - Sargent ASSA ABLOY IDP-H1 Installation Instructions Manual

Harmony Series IDP-H1 Mortise Lock

General Description

2
The SARGENT Harmony Series IDP-H1 Mortise Lock is designed to interface with Wiegand Electronic
Access Control (EAC) panels. The reader requires 12VDC for power and is available with 125kHz HID proximity
technology. The H1 technology is backed by SARGENT Grade 1 hardware.
The mortise lock includes both Request to Exit (RX) and door position monitoring inside the lock body.
Featuring EcoFlex™ technology*, the H1 mortise lock is field-configurable to fail-safe or fail-secure and operates
from 12-24VDC. Weather seal gaskets are also included for outside use on exterior door applications only.
The Harmony H1 reader provides visual (LED) and audible indication of lock state (locked/unlocked).
This product offers an Integrated Door Position Switch in the mortise lock body. The magnetic switch is wired
in series with the latchbolt (LX) and auxiliary bolt (AX), offering added security and improved aesthetics.
*Sargent Manufacturing Company (New Haven, CT) 2015 U.S. Patents D601,001S; D601,002S; D601,003S; D602,762S; Patent Pending
HID and Edge are trademarks or registered trademarks of HID Global Corporation.

Hardware Specifications

3
• Latch - Stainless steel 3⁄4" projection one-piece
• Deadbolt - One-piece hardened stainless steel
• Guardbolt - Stainless steel, non-handed
• Handed - Easily field reversible without opening case
• Case - 12 gauge heavy duty wrought steel
• Outside lever controlled by any 125kHz HID
proximity credential
• Inside lever provides RX signal and retracts latch
and deadbolt
Electrical Specifications
4
12/24VDC System
• Reader Draw = 140mA @12VDC
• Actuator Draw = 15mA continuous
• Maximum (2) locks per 1 Amp power supply
(1/2 Amp peak current draw)
The H1 reader requires 12VDC for power.
As the lock accepts 12-24V, a 12V power supply
is recommended to support both the lock and
reader with a single power supply.
Total
One-Way
Length of
Wire Run (ft) 1/4A 1/2A
100 20 18
150 18 16
200 16 14
250 16 14
300 16 12
400 14 12
500 14 10
750 12 10
1,000 10 —
1,500 10 —
A8132C • 800-810-WIRE (9473) • www.sargentlock.com
Wire Gauge Charts
Load Current @ 12VDC
3/4A 1A 1-1/4A 1-1/2A 2A
16 14 14 12 12
14 12 12 12 10
12 12 10 10 —
12 10 10 10 —
12 10 10 — —
10 — — — —
10 — — — —
— — — — —
— — — — —
— — — — —
• Door position switch (DPS) within lock body
• Magnetic switch is wired in series with the latch-
bolt (LX) and auxiliary bolt (AX)
• Maximum 1/4" gap allowed between door
and strike
• Locks furnished for 1-3/4" doors. Other door
thicknesses require confirmation with factory.
• UL and CUL listed for use on Fire Doors
• Wire from EAC panel to door must be shielded
with drain terminated at EAC Panel controller
McKinney
Electric
Total
One-Way
Length of
3A Wire Run (ft) 1/4A 1/2A
10 100 24 20
— 150 22 18
— 200 20 18
— 250 18 16
— 300 18 16
— 400 18 14
— 500 16 14
— 750 14 12
— 1,000 14 10
— 1,500 12 10
3
Wiegand Access
Control System
Hinge
Harmony
Series H1 Patented
Load Current @ 24VDC
3/4A 1A 1-1/4A 1-1/2A 2A
18 18 16 16 14
16 16 14 14 12
16 14 14 12 12
14 14 12 12 12
14 12 12 12 10
12 12 10 10 —
12 10 10 — —
10 10 — — —
10 — — — —
— — — — —
3A
12
10
10
10
—
—
—
—
—
—