Sargent Profile Series Installation Instructions Manual
Mortise lock with aperio technology
Hide thumbs
Also See for Profile Series:
- Installation instructions manual (22 pages) ,
- Installation instructions manual (11 pages)
Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Sargent Profile Series
Summary of Contents for Sargent Profile Series
- Page 1 Certification Exhibit FCC ID: U4A-SCYICLS1 IC: 6982A-SCYICLS1 FCC Rule Part: 15.247 / 15.225 IC Radio Standards Specification: RSS-210 ACS Project Number: 10-0345 Manufacturer: Assa Abloy Model: N2-IA/IK Manual 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598...
- Page 2 Aperio™ Technology Mortise Lock Installation Instructions A8078A 04/11 Copyright 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
-
Page 3: Table Of Contents
Table of Contents Warning ...................2 General Description ..............3 Specifications ................3 System Overview ..............3 Parts Breakdown ..............4 Lock Installation ..............6 Operational Check ..............14 Lock LED Indications ............15 Warning: Changes or modifications to this device not expressly approved by ASSA Warning ABLOY could void the user’s authority to operate the equipment. FCC: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. -
Page 4: General Description
– the wiring at the door. The Profile Series v.N2 includes HID ® iCLASS ® 13.56 MHz smart card tech- nology, and all technology features are supported by the physical security of SARGENT ANSI/BHMA Grade 1 hardware. -
Page 5: Parts Breakdown
Profile Series v.N2 Mortise Lock Parts Breakdown 13.56 MHz iCLASS 1-800-810-WIRE • www.sargentlock.com • A8078A... - Page 6 Profile Series v.N2 Mortise Lock Parts Breakdown 13.56 MHz iCLASS (Continued) ITEM PART NO. DESCRIPTION QTY. Outside Lever Reference 8200 Catalog for available levers Inside Lever Reference 8200 Catalog for available levers 82-0495 O/S Escutcheon only with Cylinder 82-0493 O/S Escutcheon only without Cylinder...
-
Page 7: Lock Installation
Profile Series v.N2 Mortise Lock Lock Installation 1 Prepare Door A. Verify Hand and Bevel of Door Stand on outside of locked door when determining door hand. LHRB RHRB Left Hand Left Hand Right Hand Right Hand Hinges Left Reverse Bevel... - Page 8 Profile Series v.N2 Mortise Lock 2 How to Change Hand of Lock body A. Reverse Lock Hand Red surface of locking piece must face the outside/locked side of door. To rotate locking piece (Fig. 2A): 1. Position lock body with red surface of locking piece visible.
- Page 9 Profile Series v.N2 Mortise Lock 3 Mortise Lock Body DIP Switch Settings NOTE: The DIP switch RX settings located on the rear of the mortise lockbody must be set prior to lock installation. Failure to follow sticker directions will cause inaccurate RX activity to be reported to the access control panel.
- Page 10 Profile Series v.N2 Mortise Lock 5 Exterior Door Options A. Fire Stop Plate (P/N 52-0033) Fire-rated doors require a fire stop plate on the outside of the door (Fig. 5A). 1. Drill (2) 1/8” x 1-1/4” deep holes in the door, if not already present.
- Page 11 Profile Series v.N2 Mortise Lock 7 Install Outside Escutcheon 1. Attach escutcheons to the door after the wires are connected. Note: The 43 cylinder may be used with or without a gasket. 2A. For fire rated doors: Feed ribbon cable with connector from outside of door through weatherseal gasket and fire stop plate (Fig.
- Page 12 Profile Series v.N2 Mortise Lock 9 Inside Escutcheon Connections Before the controller is attached to the door: 1. Connect the cable from the mortise lock to the bottom of the controller assembly (TB1). 2. Attach the reader assembly ribbon cable into the controller assembly (2).
- Page 13 Note: The 43 cylinder may be used when installing this product with or without a gasket. Note: SARGENT logo must be horizontal and on the top of the cylinder (Fig. 12B). 2. Secure the cylinder by tightening the cylinder clamp screw located above the deadbolt using a #2 Phillips screwdriver (Fig.
- Page 14 Profile Series v.N2 Mortise Lock 13 Attach Front Plate Attach front plate with (2) flat head screws. Outside of Door Fig. 13A 14 install or Replace Batteries 1. To install or replace batteries, first remove the battery cover (if necessary) using the provided security tool (Fig.14A).
-
Page 15: Operational Check
Profile Series v.N2 Mortise Lock Operational Check For 82276- and 82278-function mortise locks with cylinders: 1. Insert key into cylinder and rotate. There should be no friction against lock case, wire harness or any other obstructions. (Refer to Section -6 Wiring if harness friction exists). -
Page 16: Lock Led Indications
Profile Series v.N2 Mortise Lock Lock LED Indications 1 Lock Normal Operation LED indication The lock has three LEDs that support an optical scheme with red, yellow and green. The indication scheme is described by the figures below: Card read One yellow flash (.25 second) - Page 17 New Haven, CT 06511 USA 800-810-WIRE (9473) • www.sargentlock.com Founded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices, electro-mechanical products and access control systems for new construction, renovation, and replacement applications. The company’s customer base includes commercial construction, institutional, and industrial markets.
Need help?
Do you have a question about the Profile Series and is the answer not in the manual?
Questions and answers