LINET Image 3 B Instructions For Use And Technical Description page 16

► Follow the instructions for use carefully.
► Any non-observance of this manual may lead to injuries or material damage.
► Exclusively use the bed if it is in perfect working order.
► If necessary, check the bed functions daily or at each shift change.
► Use the bed exclusively in its original condition.
► Use the bed exclusively with the correct mains supply.
► Ensure that the bed is operated exclusively by qualified personnel who have been trained according to the instructions for
use.
► Ensure that the patient (health permitting) has been informed about the operation of the bed and all applicable safety
instructions.
► Move the bed exclusively on even, hard-surfaced floors.
► Replace any damaged parts immediately with original spare parts.
► Ensure that maintenance and installation are performed exclusively by qualified personnel who have been trained by the
manufacturer.
► Do not apply excess weight or loads to the bed according to SWL (safe working load).
► During peak loads or unavoidable excess loads (CPR), place mattress platform in the lowest position.
► Ensure that only one adult patient uses the bed at any time.
► Take care to avoid injuries or squeezing when operating moving parts.
► When using lifting poles or infusion stands, ensure that nothing will be damaged when you move or adjust the bed.
► Ensure that castors are braked when the bed not being moved, regardless of whether the bed is occupied or empty
► Keep the mattress platform in the lowest position at any time when the healthcare personnel are not treating the patient in
order to prevent the patient from falling or injuries.
► Ensure that siderails are operated exclusively by healthcare personnel.
► Never use the bed in areas where there is a hazard of explosion.
► Enable or disable functions on the handset using the Attendant Control Panel as appropriate for the patient's physical and
mental state. Verify that the function is actually disabled.
► Never handle the mains plug with wet hands.
► Unplug the mains cable exclusively by pulling on the plug.
► Position the mains cable so that there are no loops or bends in the cable; protect the cable from mechanical wear and tear.
► Improper handling of mains cable can cause an electric shock hazard, other serious injuries or damage to the bed.
► Ensure that the stipulated duty cycle (on-time) is not exceeded (see INT. on product label).
► Ensure that the moving parts of the bed are not blocked.
► To prevent failures, use exclusively the manufacturer's original accessories and mattresses.
► Ensure that the stipulated safe working load is not exceeded.
► If the patient's condition could lead to an entrapment, leave the mattress support platform in the flat position while the
patient is unattended.
► Adjust bed height to approx. 20 cm below maximum height when transporting the bed in order to facilitate overcoming
possible obstacles.
► Do not exceed maximum load of 75 kg for mattress platform extension.
► Ensure that the bed and its components are exclusively modified with the manufacturer´s approval.
► Ensure there is no risk of crushing or otherwise injuring the patient's limbs (e.g. between siderails and mattress platform,
between movable parts etc.) before positioning the bed or folding down the siderails.
► Close linen shelf before using the Antitrendelenburg position.
► Do not put any objects (e.g. accessories, infusions, cables) between or on siderails and movable parts.
► Use exclusively split plastic or split telescopic siderails for confused or disoriented patients.
► Before setting the extra-low position, ensure there is no risk of any parts of the bed colliding with servers, accessories or
body parts.
► Ensure there is no risk of damaging the cables of Attendant Control Panel or handset when they are stored on siderails or
head board/foot board.
► To prevent collisions, do not put oxygen bottle holders directly under mattress platform.
► Always set mattress platform to its lowest position and single parts of mattress platform to horizontal position in case the
patient is left on the bed without supervision of personnel and if his health and mental status may indicate increase risk of
falling out of the bed or entrapment.
► Personnel must consider overall adjustment of the bed and locking all of the positioning functions in accordance to health
and mental status of patient, especially if the patient is left without supervision (even for short period of time) of the
personnel.
► Manual positioning of parts of the bed which are designed for electronic positioning (e.g. backrest) is forbidden. Otherwise
there is a risk of damaging and dysfunction of the backrest actuator or unprompted fall of the backrest.
16 D9U001AM2-0101_06