Kubota M7132 Operator's Manual page 312

TROUBLESHOOTING
Error or warning code
Engine con-
trol unit
SPN
VCU2 521011
VCU2 522004
VCU2 522005
VCU2 522006
VCU2 522007
VCU2 522015
VCU2 522017
VCU2 522029
VCU2 522030
VCU2 522031
VCU2 522032
VCU2 522034
VCU2 522035
VCU2 522035
VCU2 522078
VCU2 522078
VCU2 522081
VCU2 522082
VCU2 522083
306
Type of trouble
FMI
Signal error; remote control valve
9
switch.
Operational error for PTO lever
7
and PTO switch.
Signal error; external rear PTO
9
switch left is kept being pressed.
Signal error; external rear PTO
9
switch right.
9 Signal error; rear PTO switch.
9 Signal error; front PTO switch.
3 or 4 Wheel angle sensor error.
Shuttle lever forward position er-
2, 3, 4, 5 or 9
ror.
Shuttle lever reverse position er-
2, 3, 4, 5 or 9
ror.
Shuttle lever neutral position er-
2, 3, 4, 5 or 9
ror.
2, 3 or 9 Shuttle lever safety position error.
No record input of headland man-
24
agement system.
Headland management system
25
operation is being stopped.
Headland management system
26
operation is being stopped.
Front suspension stroke sensor
3 or 4
error.
Front suspension stroke sensor
13
error.
Signal error; front suspension au-
9
to mode switch.
Signal error; front suspension
3
block mode switch.
Signal error; front suspension
3
"UP" switch.
Action
Check if the remote control valve switch is stuck.
If the message persists after the switch is released,
contact your dealer.
Ensure the PTO gear shift lever and PTO operating
mode select lever position are not in neutral posi-
tion, when the PTO switch is on.
Check if the external rear PTO switch left is stuck.
If the message persists after the switch is released,
contact your dealer.
Check if external rear PTO switch right is stuck.
If the message persists after the switch is released,
contact your dealer.
Check if the rear PTO switch is stuck.
If the message persists after the switch is released,
contact your dealer.
Check if the front PTO switch is stuck.
If the message persists after the switch is released,
contact your dealer.
Wheel angle sensor or wiring may be defective;
contact your dealer.
This happens when the shuttle lever is held in for-
ward position for a long time.
If the problem persists, contact your dealer.
This happens when the shuttle lever is held in re-
verse position for a long time.
If the problem persists, contact your dealer.
This happens when the shuttle lever is held in neu-
tral position (lever down) for a long time.
Please stop the engine once, and restart. If the
problem persists, contact your dealer.
This happens when the shuttle lever is held in safe-
ty position (lever up) for a long time.
If the problem persists, contact your dealer.
When programming the headland management sys-
tem, push the recording button again and operate
the tractor.
Replay headland management system during driv-
ing.
Check if the rear hitch is blocked.
Replay headland management system after releas-
ing the hydraulic block.
Front suspension sensor or wiring may be defective;
contact your dealer.
Front suspension sensor or wiring may be defective;
contact your dealer.
Check if the front suspension auto mode switch was
held in on for a long time.
Otherwise, contact your dealer.
Check if the front suspension block mode switch
was held in on for a long time.
Otherwise, contact your dealer.
Check if the front suspension "UP" switch was held
in on for a long time.
Otherwise, contact your dealer.
(Continued)
M7132, M7152, M7172