Error Messages - Broadcom 5720ZG User Manual

Broadcom NetXtreme Ethernet Adapter • Diagnostic User's Guide

11 ERROR MESSAGES

/* NO_ERROR
/* ERR_IND_REG_ERR
/* ERR_CHIP_RUNNING
/* ERR_BAD_NIC
/* ERR_READ_ONLY_CLEAR
offset 0x%X",
/* ERR_READ_ONLY_SET
offset 0x%X",
/* ERR_READ_WRITE_NOT_CLEAR
zero at offset 0x%X",
/* ERR_READ_WRITE_NOT_SET
offset 0x%X",
/* ERR_BIST
/* ERR_INTERRUPT
/* CMD_ABORT
/* ERR_DMA_TXDATA
/* ERR_DMA_RXDATA
/* ERR_TXDMA
/* ERR_RXDMA
/* ERR_MEM
/* ERR_MEM2
0x%08X",
/* ERR_EEP_WRITE
/* ERR_EEP_READ
/* ERR_EEP_DATA
0x%08X",
/* ERR_FILE_OPEN
/* ERR_BAD_CPU_CFG
/* ERR_IMAGE_SIZE
/* ERR_MALLOC
/* ERR_CPU_RESET
/* ERR_CPU_NO_RESP
/* ERR_CPU_TEST
/* ERR_DMA_RANGE
0x%08X-0x%08X and exclude 0x%08X-0x%08X",
/* ERR_DMA_DATA
data=0x%02X @ 0x%08X",
/* ERR_PHY_ID
/* ERR_PHY_TOO_MANY_REG
/* ERR_VPD_WRITE
/* ERR_VPD_DATA
/* ERR_NO_LINK
/* ERR_DATA_TX
/* ERR_DATA_TX_MISSING
/* ERR_DATA_RX_MISSING
received\n%d unknown packets have been received.\n%d bad packets have been received.",
/* ERR_INVALID_TEST
/* ERR_EEPROM_CHECKSUM
/* ERR_READING_WOL_PXE
/* ERR_READING_WOL_PXE
/* ERR_NO_EXT_SRAM
/* ERR_DMA_LEN
%04X",
/* ERR_FILE_TOO_BIG
/* ERR_INVALID
/* ERR_WRITE
/* CMD_QUIT
/* ERR_CPU_MEM_ERR
%08X",
/* ERR_ENDIF
/* ERR_ROM_D_DATA
0 */ "",
1 */ "Got 0x%08X @ 0x%08X. Expected 0x%08X",
2 */ "Cannot perform task while chip is running",
3 */ "Invalid NIC device",
4 */ "Read only bit %s got changed after writing zero at
5 */ "Read only bit %s got changed after writing one at
6 */ "Read/Write bit %s did not get cleared after writing
7 */ "Read/Write bit %s did not get set after writing one at
8 */ "BIST failed",
9 */ "Could not generate interrupt",
10 */ "Aborted by user",
11 */ "Tx DMA:Got 0x%08X @ 0x%08X. Expected 0x%08X",
12 */ "Rx DMA:Got 0x%08X @ 0x%08X. Expected 0x%08X",
13 */ "Tx DMA failed",
14 */ "Rx DMA failed",
15 */ "Data error, got 0x%08X at 0x%08X, expected 0x%08X",
16 */ "Second read error, got 0x%08X at 0x%08X, expected
17 */ "Failed writing NVRAM at 0x%04X",
18 */ "Failed reading NVRAM at 0x%04X",
19 */ "NVRAM data error, got 0x%08X at 0x%04X, expected
20 */ "Cannot open file %s",
21 */ "Invalid CPU image file %s",
22 */ "Invalid CPU image size %d",
23 */ "Cannot allocate memory for size %d",
24 */ "Cannot reset %cX CPU",
25 */ "%cx CPU does not respond",
26 */ "%cx CPU test failed",
27 */ "Invalid Test Address Range\nValid NIC address is
28 */ "DMA:Got 0x%02X @ 0x%08X. Expected 0x%02X\nSRAM
29 */ "Unsupported PhyId %04X:%04X",
30 */ "Too many registers specified in the file, max is %d",
31 */ "Cannot write to VPD address %04X",
32 */ "VPD data error, got %08X @ 0x%04X, expected %08X",
33 */ "No good link! Check Loopback plug",
34 */ "Cannot TX Packet!",
35 */ "Requested to Tx %d. Only %d is transmitted",
36 */ "Expected %d packets. Only %d good packet(s) have been
37 */ "%c%d is an invalid Test",
38 */ "NVRAM checksum error",
39 */ "Error in reading WOL/PXE",
40 */ "Error in writing WOL/PXE",
41 */ "No external memory detected",
42 */ "DMA buffer %04X is too large, size must be less than
43 */ "File size %d is too big, available space is %d",
44 */ "Invalid %s",
45 */ "Failed writing 0x%x to 0x%x",
46 */ "",
47 */ "%s CPU access error @ %08X, expected %08X but got
48 */ "",
49 */ "ROM disable error, data returned while disabled",
page 140
Broadcom Confidential and Proprietary