Broadcom 5720ZG User Manual page 151

Broadcom NetXtreme Ethernet Adapter • Diagnostic User's Guide
/* ERR_GPIO5704
%d/%d/%d",
/* ERR_BIST_NOT_DONE
/* ERR_BIST_DATA_MISCMP
/* ERR_CPU_NO_RESPONSE
/* ERR_CPU_ERR_CODE
/* CMD_LOOP
/* CMD_SKIP
/* CMD_ELSE,
/* CMD_ELSEIF,
/* CMD_BREAK,
/* CMD_ENDWHILE,
/* ERR_BYTE,
/* ERR_WORD,
flshdg5x.bin v2.3 or newer)",
/* ERR_NO_LINK_DOWN
/* ERR_MISMATCHED_DEVICEID
match with board %d",
/* ERR_INVALID_DATA_SIZE
/* ERR_MAC_ADDR_ENDED
/* ERR_ILLEGAL_MAC_ADDR
/* ERR_BIST_DATA_INVALID
/* ERR_INVALID_BOND_ID
/* ERR_BAD_CPU_RESET
/* ERR_INCORRECT_VERSION
/* ERR_MISMATCH_CFG_VERSION 124 */ "Mismatched CFG and FW Image version",
/* ERR_NOT_SUPP_CFG_BW
/* ERR_POST_1G_LB
/* ERR_DRIVER
function",
/* ERR_TXDMA_OVERFLOW
/* ERR_RXDMA_OVERFLOW
/* ERR_DRIVER_BAD_STATUS
/* ERR_INVALID_HANDLE
/* ERR_SOCKET
/* ERR_SIOCGIFINDEX
/* ERR_BIND
/* ERR_SETSOCKOPT
/* ERR_FCNTL
/* ERR_SEND
/* ERR_RECEIVE
/* ERR_FALSE_CARRIER
/* ERR_INV_OPT
/* ERR_INV_DEV
/* ERR_IRQ
/* ERR_TIMEOUT
/* ERR_PKT_DATA
recevied %02X",
/* ERR_MAC_ZERO
/* ERR_MAC_MIS_REG
%02X.",
/* ERR_CPU_ACC
/* ERR_CPU_MEM
/* ERR_CPU_INSTR
/* ERR_BUS_LINK
/* ERR_ASF_FILE_VER
/* ERR_ASF_VS_DEV
/* ERR_MISMATCHED_DEVICEID_1
not match with board %d",
/* ERR_MISMATCHED_DEVICEID_2
match with unknown board",
/* ERR_CPU_FETCH
/* ERR_UMPLB
/* ERR_UMPCTRL
/* ERR_REG_TABLE
/* ERR_FW_IMAGE_SIZE
size (%d)",
/* ERR_MISS_PXE
/* ERR_MISS_ASF
/* ERR_NVRAM_DIR
/* ERR_MISS_UMP
102 */ "Dev:%d Expected GPIO 0/1/2 = %d/%d/%d, but read as
103 */ "Bist test did not complete internally",
104 */ "Bist data miscompared at bit: %d out: %d exp: %d",
105 */ "No Response from firmware",
106 */ "%s CPU returned result %d, key = %d",
107 */ "",
108 */ "",
109 */ "",
110 */ "",
111 */ "",
112 */ "",
113 */ "Byte access error: expected %02x at %08x but got %02x",
114 */ "Wrd acc err: exp %04x at %08x but got %04x (need
115 */ "No link down found",
116 */ "bootcode Image file belongs to %d family, does not
117 */ "Invalid data size",
118 */ "Runs out of Mac Address",
119 */ "Illegal Mac Address",
120 */ "Invalid bist data from buffer at %d",
121 */ "Invalid bond id",
122 */ "CPU reset failed, register 5034 is 0x%x",
123 */ "Incorrect version",
125 */ "Current ASF_T_VERSION is not backward compatible",
126 */ "1G Tx/Rx Lines Have A Short/Open",
127 */ "Driver %d.%d.%d or later is required to run this
128 */ "TxDMA Overflow",
129 */ "RxDMA Overflow",
130 */ "Driver returned error status=%d",
131 */ "Invalid Handle",
132 */ "Socket open error%d %s",
133 */ "ioctl(): SIOCGIFINDEX failed",
134 */ "bind() failed: %s",
135 */ "setsockopt() failed:%d %s",
136 */ "fcntl() failed:%d %s",
137 */ "send() failed (cnt=%d): %d %s",
138 */ "recvfrom() failed (cnt=%d): %d %s",
139 */ "Error! False Carrier Detected During The Test",
140 */ "Invalid Options",
141 */ "Found Rv = %s, Expected Rv = %s due to -ckdev value",
142 */ "Invalid IRQ %d",
143 */ "Timeout",
144 */ "Packet data error at offset %d, expected %02X but
145 */ "Zero Mac Address in Mac Register",
146 */ "Mac Address MisMatch: Got %02X-%02X-%02X-%02X-%02X-
147 */ "%cx CPU failed on %s bit access to address %08X",
148 */ "%cx CPU failed on memory pattern %08X at address %08X",
149 */ "%cx CPU Instruction test failed",
150 */ "PCI-E Bus Link Error",
151 */ "ASF File versions Error",
152 */ "ASF VS Device Error",
153 */ "bootcode Image file belongs to unknown family, does
154 */ "bootcode Image file belongs to %d family, does not
155 */ "CPU Fetch Test Error: Breakpoint reads %x",
156 */ "UMP loopback failed, Total Good packet %d",
157 */ "Error: UMPCtrl 0x5F0 = %x",
158 */ "Error: Unable to create Reg Table",
159 */ "Error: Firmware image size (%d) larger than NVRAM
160 */ "Error: %s firmware cannot be found in %s",
161 */ "Error: %s firmware cannot be found in %s",
162 */ "Error: NVRAM Directory",
163 */ "Error: %s firmware cannot be found in %s",
page 142
Broadcom Confidential and Proprietary