Broadcom 5720ZG User Manual page 150

Broadcom NetXtreme Ethernet Adapter • Diagnostic User's Guide
/* ERR_CHIP_NOT_RUNNING
driver)",
/* ERR_NO_REG_DEF
/* ERR_ASF_RST
/* ERR_ASF_ATTN_LOC
/* ERR_ASF_RST_VAL
/* ERR_ASF_PA_TIMER
/* ERR_ASF_PA_CLEAR
/* ERR_ADF_NO_STAMP
/* ERR_ADF_NO_TIMER
/* ERR_ASF_EVENT
/* ERR_EEP_FILESIZE
bytes",
/* ERR_MAGIC_VALUE
%08x",
/* ERR_EEP_FMT
%c",
/* ERR_EEP_BOOTVER
%d.%d",
/* ERR_EEP_CANNOT_WRITE
/* ERR_EEP_CANNOT_READ
/* ERR_BAD_CHECKSUM
/* ERR_BAD_MAGIC_VALUE
/* ERR_MAC
%02X",
/* ERR_BUS
%02X:%02X:00",
/* ERR_SPEC_MEM
0x%08x-0x%08x\nGot 0x%08x @ address 0x%08x. Expected 0x%08x",
/* ERR_NOT_SUPPORT
/* ERR_BAD_CRC
/* ERR_MII_ERR_BITS_SET
/* ERR_INIT_MAC
correctly",
/* ERR_FW_FILE_FORMAT
/* ERR_RESET_TX_CPU
/* ERR_RESET_RX_CPU
/* ERR_INVALID_MAC_ADDR
/* ERR_MAC_REG
/* ERR_BOOTCHECKSUM
/* ERR_VPD_READONLY
%08X at %04X",
/* ERR_VPD_READ
/* ERR_MEM_READ
/* ERR_MEM_WRITE
/* ERR_PXE_PGM
/* ERR_PXE_VFY
/* ERR_EXT_MEM_EXE_TIMOUT
/* ERR_EXT_MEM_SIZE
/* ERR_RESET_TIMEOUT
/* ERR_MSI_ERR_NOTCLEAR
/* ERR_MSI_DATA
/* ERR_MEM_INIT
/* ERR_MEM_UNINIT
/* ERR_PCI_REGS_WIDTH
expected at offset 0x%X",
/* ERR_LINK_STATUS
/* ERR_PHY_INTERRUPT
/* ERR_EEP_BIT_BANG
/* ERR_ROM_SIZE
(0x30) register with %d written to ROM size reg.(0x88)",
/* ERR_ROM_DATA
/* ERR_ROM_ENABLE
firmware",
/* ERR_GPIO
50 */ "Cannot perform task while chip is not running. (need
51 */ "Cannot open register define file or content is bad",
52 */ "ASF Reset bit did not self-cleared",
53 */ "ATTN_LOC %d cannot be mapped to %cX CPU event bit %d",
54 */ "%s Regsiter is not cleared to zero after reset",
55 */ "Cannot start poll_ASF Timer",
56 */ "poll_ASF bit did not get reset after acknowleged",
57 */ "Timestamp Counter is not counding",
58 */ "%s Timer is not working",
59 */ "Cannot clear bit %s in %cX CPU event register",
60 */ "Invalid %s file size, expected %d but only can read %d
61 */ "Invalid magic value in %s, expected %08x but found
62 */ "Invalid manufacture revision, expected %c but found
63 */ "Invalid Boot Code revision, expected %d.%d but found
64 */ "Cannot write to NVRAM",
65 */ "Cannot read from NVRAM",
66 */ "Invalid Checksum",
67 */ "Invalid Magic Value",
68 */ "Invalid MAC address, expected %02X-%02X-%02X-%02X-%02X-
69 */ "Slot error, expected an UUT to be found at location
70 */ "Adjacent memory has been corrupted while testing block
71 */ "The function is not Supported in this chip",
72 */ "Packets received with CRC error",
73 */ "MII error bits set: %04x",
74 */ "CPU does not initialize MAC address register
75 */ "Invalid firmware file format",
76 */ "Resetting TX CPU Failed",
77 */ "Resetting RX CPU Failed",
78 */ "Invalid MAC address",
79 */ "Mac address registers are not initialized correctly",
80 */ "NVRAM Bootstrap checksum error",
81 */ "Write operation changed VPD read only data from %08X to
82 */ "Cannot read data from VPD address %04X",
83 */ "Memory read and compare error",
84 */ "Memory write error",
85 */ "PXE Programming Error",
86 */ "PXE Verification Error",
87 */ "Cannot execute code from external memory, pc=%08X",
88 */ "External memory size detection error",
89 */ "Reset Time",
90 */ "MSI Error bits are not cleared after reset",
91 */ "MSI expected %04X, but read %04X at %08X",
92 */ "mem pool initialization failed",
93 */ "mem pool un-initialization failed",
94 */ "Read/Write PCI regs width %d affects wider than
95 */ "Link status error in auto-polling mode",
96 */ "Phy interrupt did not happen",
97 */ "EEprom test fails in bit-bang mode at address %X",
98 */ "ROM size error\nExpected %08X but read %08X at\nROM Bar
99 */ "Data Error\nExpected %08X but read %08X at %08X",
100 */ "Expansion ROM Desired bit is not set after loading
101 */ "GPIO%d Error, write=%d, read=%d",
page 141
Broadcom Confidential and Proprietary
/* no longer in use */