Yamaha RS7000 Owner's Manual page 45

6 Go to the Sampling Standby Page
Press [F4] (OK) to go to the sampling standby page.
7 Set the Trigger Mode/Level
Use [Knob 3] (TRIGGER MODE) to set the trigger mode to "LEVEL", and [Knob 4] (TRIGGER LEVEL) to set the trigger level to
"64". Play your source or speak into the microphone at this point to make sure that the level bar graph extends past the triangular trigger
level marker below the level meter, but doesn't "peak out" due to excessively high input levels (you're not actually sampling yet). If the
level is too low or high, use the REC VOLUME control to adjust as necessary. If the REC VOLUME control doesn't allow sufficient
adjustment, recheck your INPUT GAIN setting (step 3, above) or change the Trigger Level setting as required.
Refer to page 232 for information on the other available trigger modes.
8 Press [STANDBY/START/STOP] to begin sampling
Pressing [STANDBY/START/STOP] engages the trigger wait mode, and sampling will begin automatically as soon as the input signal
exceeds the specified trigger level. Since the KIT+NOTE sampling type is selected sequence playback will begin automatically when
the [STANDBY/START/STOP] button is pressed. Sampling will always be synchronized with sequencer playback — in other words,
your sample will be placed in the pattern at exactly the point you begin recording.
9 Stop Sampling
Press the [STANDBY/START/STOP] button to stop sampling when your sample is recorded. Sampling will also stop automatically
when the end of the pattern is reached. The sampling mode will be exited when sampling ends.
0 Play and Check the Results
Press [PATTERN] to select the PATTERN Play or PATTERN Patch page, then press the [PLAY] button to play back the pattern and
check the results.
Editing Your Sample
If all went well your vocal hit will play back with the pattern in precisely the location it was recorded (this is because the
KIT+NOTE sample type was selected. You might also want to loop, slice, or modify the way your sample plays back in
other ways. Refer to "Chapter 5: The Sampling Mode" beginning on page 227 for complete information on all of the sam-
ple editing functions provided by the RS7000.
MASTER EFFECT
EFFECT
ON/OFF
F1 F2
NUM
REC
SHIFT
REC VOLUME KEY- ARPEGGIO OCT OCT
BOARD ON DOWN UP
SECTION A B
TRANSPOSE
CAPS ALL 1~8
TRACK 1 2 3
MUTE
SOLO
K ! L # M $ N %
TRACK 3.3V CARD
SELECT
MUSIC PRODUCTION STUDIO
Integrated Sampling Sequencer
SAMPLING
MULTI COMP RING MOD REAL TIME
CTRL DELAY V-DIST
LOOP SAMPLE STANDBY IN
D-FILTER LO-FI REMIX EDIT
OUT A
ISOLATION SLICE
OUT B
START/STOP
REC VOLUME MIDI MASTER VOLUME
SEQUENCE PLAY FX EFFECT SEND / VOLUME
SELECT
BEAT STRETCH CLOCK SHIFT SWING DRY VARI DELAY/CHO REVERB TRACK VOLUME
GATE TIME MIDI DELAY VELOCITY
LFO EG
WAVE
AMP
FILTER
S&H
USER PITCH ATTACK DECAY SUSTAIN RELEASE
SPEED PGM DEPTH
PITCH FILTER
- +
PORTAMENTO LPF24
TYPE FINGERED TYPE
LPF18
FULL TIME LPF12
OFF HPF
BPF
PITCH BEND PORTAMENTO TIME CUTOFF RESONANCE ENV.DEPTH
BEF
F3 F4
MODE
PATTERN PATT SONG UTILITY UTILITY
CHAIN
SYSTEM
MIDI SETUP MIDI FILTER
BPM SUB MODE
GROOVE PLAY FX MIDI DELAY MIXER GROOVE PLAY FX MIDI DELAY MIXER
GRID GROOVE HARMONIZE MIDI DELAY VOICE SELECT
STOP PLAY NOTE FEEDBACK VOL/PAN/OUT
TIME EQ
EFFECT SEND
7 8 9 + - / LEVEL
VOICE EDIT EFFECT SETUP MASTER VOICE EDIT EFFECT SETUP MASTER
LFO EFFECT TYPE ARPEGGIO MASTER EQ
PORTAMENTO VARIATION A/D SETUP MASTER
MUTE EG PITCH DELAY REVERB MIDI OUT CH KNOB ASSIGN EFFECT
MEMORY 4 5 6 0 FILTER
STORE SCENE 1 2 3 4 5 EXIT SAVE LOAD JOB EDIT SAVE LOAD JOB EDIT
SAVE LOAD JOB LIST EDIT CHANGE
EXPORT IMPORT VIEW FILTER
RENAME SCSI SETUP
DELETE SCSI COMM
1 2 3 ENTER FORMAT
C D E F G H I J
TAP
PAD 1 PAD 2
9~16 TR- TR+ PAD ASSIGN
4 5 6 7 8 9 10 11 12 13 14 15 16
SPACE DEL
O & P ' Q ( R ) S - T @ U ^ V _ W { X } Y ~ Z
TRANSPOSE(-) TRANSPOSE(+)
5. Add Samples
T
UTORIAL
RS7000 45